"Click" or Woodloc systems: there are a number of patented "click" systems that now exist. These click systems are either "unilin" or "fiboloc" A "click" floor is similar to tongue-and-groove, but instead of fitting directly into the groove, the board must be angled or "tapped" in to make the curved or barbed tongue fit into the modified groove. No adhesive is used when installing a "click" floor, making board replacement easier. This system not only exists for engineered wood floors but also engineered bamboo and a small number of solid floors (such as "parador solido click") and is designed to be used for floating installations. It is beneficial for the Do-It-Yourself market.

The age of your floor also plays a role. If your floor has been in place for decades, it may resist refinishing for a number of reasons. For instance, if it has already been refinished several times or if too much of the surface wood has become exposed, refinishing your floor may have little effect. For very old floors, replacement can often be preferable to refinishing. Denver Hardwood Floor


The Blue Ridge Hickory Morning Fog 3/4 in. The Blue Ridge Hickory Morning Fog 3/4 in. Solid Hardwood Flooring is sealed with an Alpha Alumina finish providing protection from every day wear. This product carries a 50-year finish warranty. Each plank features a micro beveled edge and micro beveled end. You can feel confident purchasing this product because ...  More + Product Details Close Denver Hardwood Floor

Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Floor
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Floor
 Acacia (9)  American Walnut (1)  Ash (5)  Bamboo (22)  Beech (5)  Birch (3)  Bloodwood (2)  Brazilian Cherry (10)  Brazilian Chestnut (5)  Brazilian Koa (9)  Brazilian Oak (5)  Brazilian Walnut (5)  Cumaru (3)  Curupay (2)  Hevea (4)  Hickory (27)  Maple (14)  Oak (15)  Pecan (3)  Pine (10)  Purple Heart (2)  Red Cumaru (2)  Red Maple (1)  Red Oak (40)  Short Leaf Acacia (3)  ShortLeaf Acacia (1)  Spanish Hickory (3)  Tamboril (2)  Tauari (3)  Walnut (1)  White Oak (34)

Jasper, Mazama, and the other brands of hardwood flooring we offer are premium quality, delivering everything you want in a hardwood floor - look, strength, durability, and ongoing value for properties. And we offer them to you at incredible pricing not found anywhere else. While we sell discount hardwood flooring, we will never sell cheap hardwood flooring. All of our products undergo rigorous product quality testing before we offer them to you and they are constantly rechecked for quality to ensure you always get the best products while still paying below wholesale prices. Denver Hardwood Flooring

– If you want less mess and shorter installation, replacing the floors will usually take less time than refinishing them. Refinishing hardwood floors is messy and time consuming. It’s especially challenging if you are already living in the home and have furniture everywhere. Refinishing you hardwood floors can easily take 4-5 days and during that time you can not have furniture on them nor walk on them. For some homes, this creates logistical nightmares as they can’t stay in the home nor would they want to given the smell and the mess. Alternatively, if you replace the floors with prefinished hardwood, it’s a much faster process, less messy and you can still live in the home fairly easily. I have many customers that have done this simply because they want to avoid the mess created from refinishing the hardwood floors. Denver Hardwood Flooring
When it comes to budgeting for this project, you have many factors to consider. Two of the largest considerations include the cost per square foot of the materials and the cost per square foot for installation. To help you understand the potential costs of installing hardwood, we researched the average cost per square foot for traditional and engineered flooring at three different price points. Hardwood Floor
First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional. Denver Hardwood Flooring
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7]
Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”. Hardwood Floor
Menards® has everything you need to cover your floors in style! We offer a wide selection of hardwood flooring options that are fit to use in any room of your home. Some of our quality hardwood floorcoverings include engineered hardwood, which is built to last and has higher resistance to moisture levels. We also carry a variety of solid hardwood flooring to give your home traditional character and style. If you are interested in another durable flooring option for your home, we have cork flooring. In addition to strong and durable flooring, we offer everything you will need for installation and maintenance as well as hardwood moulding and trims to help you finish the job. Once the flooring installation is complete, keep them looking clean with our selection of vacuum cleaners and floor care products. Next, complete the look with area rugs, mats, and runners to enhance your home's décor and add coziness to the space. Denver Hardwood Floor
First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional.
Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience. Denver Hardwood Flooring
Jasper, Mazama, and the other brands of hardwood flooring we offer are premium quality, delivering everything you want in a hardwood floor - look, strength, durability, and ongoing value for properties. And we offer them to you at incredible pricing not found anywhere else. While we sell discount hardwood flooring, we will never sell cheap hardwood flooring. All of our products undergo rigorous product quality testing before we offer them to you and they are constantly rechecked for quality to ensure you always get the best products while still paying below wholesale prices. Hardwood Floor
Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Denver Hardwood Floor
Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise. Denver Hardwood Flooring
First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional. Denver Hardwood Floor Install
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Floor
Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage. Denver Hardwood Floor Install
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Denver Hardwood Floor Install
Measure rooms one at a time. It’s easiest to measure rectangles, so if you have an “L-shaped” room, divide it into 2 rectangles and measure them separately. The length of the rectangle multiplied by the width equals the square footage. For example, a room, or section of a room, that is 20 feet long and 12 feet wide produces this formula: 20 x 12 = 240 square feet. If the flooring you are purchasing is sold by the yard, divide the square feet by 9. So, 240 square feet / 9 = 26.667 square yards.
When it comes to budgeting for this project, you have many factors to consider. Two of the largest considerations include the cost per square foot of the materials and the cost per square foot for installation. To help you understand the potential costs of installing hardwood, we researched the average cost per square foot for traditional and engineered flooring at three different price points. Denver Hardwood Floor Install

Michael – The exotic woods are a bit more challenging to work with stain wise because they are naturally darker and redder. Yes, you can refinish them and make them darker and browner. But, you will still have some underlying red tones. So, you may need to go darker than what you’re thinking to drown out the red more. Definitely test colors. Most likely, dark walnut will come out the darkest. Use duraseal…it’s a better stain, dries faster and is a bit darker than minwax.
When it comes to budgeting for this project, you have many factors to consider. Two of the largest considerations include the cost per square foot of the materials and the cost per square foot for installation. To help you understand the potential costs of installing hardwood, we researched the average cost per square foot for traditional and engineered flooring at three different price points. Denver Hardwood Flooring
– If you want to change the width of the wood or the direction of the hardwood, the only way to do this is to get a new floor. The standard in home is oak 2 ¼” strip. Now, it’s more stylish and more common to get wider planks such as 3 ¼” or 4”or 5” planks. These look more modern and importantly make the room look larger. Another design trick to make the rooms look larger is to lay the planks on a diagonal – that way, it carries your eye along the longest length of the room. Or, you can even get fancy and add borders or do a herringbone pattern. Denver Hardwood Floor Install
Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”. Hardwood Floor

A number of proprietary features for solid wood floors are available. Many solid woods come with grooves cut into the back of the wood that run the length of each plank, often called 'absorption strips,' that are intended to reduce cupping. Solid wood floors are mostly manufactured 0.75 inches (19 mm) thick with a tongue-and-groove for installation. Denver Hardwood Floor


Oak has always been a popular choice for hardwood flooring. The color is visually appealing, looks inviting, and has many advantages. You’ll find the wood easier to clean, and it easily blends in with furniture and home interior designs you already have. Plus, oak is a good investment if you’re considering selling your house in the future, since the wood can last for many years.
Michael – The exotic woods are a bit more challenging to work with stain wise because they are naturally darker and redder. Yes, you can refinish them and make them darker and browner. But, you will still have some underlying red tones. So, you may need to go darker than what you’re thinking to drown out the red more. Definitely test colors. Most likely, dark walnut will come out the darkest. Use duraseal…it’s a better stain, dries faster and is a bit darker than minwax.
Add style, warmth, and value to your home with beautiful hardwood floors from The Home Depot. Our hardwood floors are available in solid and engineered hardwood, and a wide variety of colors, styles and wood species. Whether you’re interested in a traditional look, like a classic oak wood floor or something more modern and contemporary, like bamboo floors or cork flooring, we have everything you need to get your flooring project done. Hardwood Floor
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Floor
No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Denver Hardwood Flooring

Hardwood species used in flooring are given a hardwood hardness rating, which indicates how resistant the wood is to dents and wear. This rating is based off a test called the Janka Hardness Test, and it measures the force needed to press a steel ball into the wood sample. The highest possible score on this test is a little over 5,000, with most traditional solid wood floors scoring in the 1,000-2,000 range. The superior density of Rigid Core flooring would exceed the limitations of the Janka test, and instead a higher impact testing is needed to measure real world performance. Here is how the general hardness of plank flooring ranks: Hardwood Floor
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank.

You cannot restore every wood floor by simply refinishing it. If your wood floor has become warped or if several of the planks have become damaged, you will typically need to replace the entire floor, as finishing will only brighten an already-damaged surface. On really old floors, you may see the tongue where the boards come together, or your boards may lack adequate thickness. Floors like this are definite candidates for replacement, as refinishing is purely cosmetic. Denver Hardwood Floor Install
Add style, warmth, and value to your home with beautiful hardwood floors from The Home Depot. Our hardwood floors are available in solid and engineered hardwood, and a wide variety of colors, styles and wood species. Whether you’re interested in a traditional look, like a classic oak wood floor or something more modern and contemporary, like bamboo floors or cork flooring, we have everything you need to get your flooring project done.
Put on gloves, knee pads, and protective eye glasses. You'll be working diligently on your hands and knees for hours to complete this project, especially if you're doing a large space. Invest in a good pair of knee pads to protect your knees. Sturdy work gloves will protect your hands from splinters, and goggles will prevent sawdust and other debris from getting into your eyes.[1] Denver Hardwood Floor
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs. Denver Hardwood Floor Install
There are some characteristics that are common to each category: solid wood is more frequently site-finished, is always in a plank format, is generally thicker than engineered wood, and is usually installed by nailing. Engineered wood is more frequently pre-finished, has bevelled edges, is very rarely site-finished, and is installed with glue or as a floating installation. [6] Hardwood Floor
Local Retailers: Local home improvement stores often carry a number of engineered wood flooring products in stock. Additionally, local flooring stores can provide samples that let you see how the color and style of the engineered floor will look in your home. Either option may offer you an on-site estimate to give you a better idea about what your project could cost. Hardwood Floor
×