Make cuts perpendicular to the direction the wood is laying. Using a circular saw, make single cuts straight across the flooring that are about 1 foot (30 cm) to 2 feet (61 cm) apart. Be sure your cuts are perpendicular to the direction of the wood. Start on 1 side of the room and work your way systematically to the other side, spacing each cut about 1 foot (30 cm) to 2 feet (61 cm) apart.[3] Hardwood Floor
Cut a new length of flooring to fit snugly into the space of the old board. It doesn't matter what kind of saw you use to repair your hardwood floors; just make sure the cuts are perfectly square. After trimming the board to length, turn it upside down and use a chisel to chop off the lower lip of the grooved edge (photo 5). That allows it to fit over the protruding tongue of the adjacent floorboard. Test-fit the new piece. If it's slightly lower than the surrounding floorboards, shim it up with strips of kraft paper. Then remove the board and spread carpenter's glue on the tongues and grooves of the new and old pieces. Slip the new board into place (photo 6), protect it with a scrap-wood block and tap it down with a hammer. Cover the board with wax paper, then hold it down overnight with heavy books or weights. An alternative to gluing: Simply face-nail the board with 6d finishing nails. Bore pilot holes at a slight angle, then drive in the nails. Tap them below the surface with a nailset (photo 7) and fill the holes with wood putty. Lightly sand the entire board smooth, but be careful not to remove too much finish from surrounding boards. After finding a matching stain color by experimenting on scraps of flooring, stain the boards to match the original floor. Let dry overnight, then apply two coats of clear polyurethane varnish. If the old floor is unstained, just apply the polyurethane.

Lowe’s has what you need to bring value-adding beauty to your home with hardwood flooring. There are plenty of species to choose from, including acacia wood flooring, walnut flooring, maple flooring, hickory hardwood flooring and cherry wood flooring. Depending on your budget and room’s traffic level, you’ll be sure to find a style to suit your needs.


Wood flooring can also be installed utilizing the glue-down method. This is an especially popular method for solid parquet flooring installations on concrete sub-floors. Additionally, engineered wood flooring may use the glue-down method as well. A layer of mastic is placed onto the sub-floor using a trowel similar to those used in laying ceramic tile. The wood pieces are then laid on top of the glue and hammered into place using a rubber mallet and a protected 2x4 to create a level floor. Often the parquet floor will require sanding and re-finishing after the glue-down installation method due to the small size pieces. Hardwood Floor

Top quality laminate will not match the look and feel of real wood floors. The areas where the planks join will wear considerably over time, and when damage sets in, it is not an easy repair. Laminate is easily damaged by moisture, and when that damage sets in, it cannot be fixed. If the laminate is not laid correctly, it will not be appealing to potential renters or buyers. Hardwood Floor
We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor.
Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection.
If your only goal is to brighten your floors and restore their original shine, consider refinishing them. But if you want to change some aspect of the floor itself, like the style of the wood, the direction of the planks or the consistency of the material, you will need to invest in a full replacement. Refinishing is ideal to restore existing wood, while replacement is ideal for establishing a completely new look or feel.
When it comes to budgeting for this project, you have many factors to consider. Two of the largest considerations include the cost per square foot of the materials and the cost per square foot for installation. To help you understand the potential costs of installing hardwood, we researched the average cost per square foot for traditional and engineered flooring at three different price points. Denver Hardwood Floor
Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Hardwood Floor

Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”. Hardwood Floor
Hardwood floors can last a long time, but eventually they need to be replaced. Luckily, it's a pretty straightforward process! Use a circular saw to cut the old hardwood into pieces, then remove the old flooring. Prepare your subflooring so that it's clean and perfectly level. After that, choose your replacement flooring and follow the process for installing that particular type of hardwood! Denver Hardwood Floor
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Denver Hardwood Floor

The amount you pay for installation depends on a variety of factors, including where you live and the intricacy of your project. For example, furniture removal and replacement, repairing the subfloor and removing and disposing of the old floor all bump up the overall cost of the project more than simply having an installer come in and lay the flooring does. To illustrate, some installers charge 20 cents per square foot for ripping up and removing carpeting or moving furniture. Others may charge a per-appliance fee for moving appliances. Denver Hardwood Flooring
Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you! Denver Hardwood Flooring
Enhance your home with beautiful hardwood flooring that Enhance your home with beautiful hardwood flooring that fits your budget. Full of abundant character and color variation Bruce Plano Gunstock Oak celebrates the beauty of natural hardwood. Enjoy natural features including mineral streaks knots and small holes and minor milling imperfections. Design your floor to your unique tastes with ...  More + Product Details Close Denver Hardwood Floor Install
Generally, hardwood floors need to be buffed every 3–5 years. The process usually takes about one day. Buffing refers to the process of using a stand up floor buffer. The floor is abraded with 180 grit screen on the buffer. This allows for the new coat of finish to mechanically adhere to the floor. This process works with great results as long as the floor hasn't had any waxes or synthetic cleaners.
There are some characteristics that are common to each category: solid wood is more frequently site-finished, is always in a plank format, is generally thicker than engineered wood, and is usually installed by nailing. Engineered wood is more frequently pre-finished, has bevelled edges, is very rarely site-finished, and is installed with glue or as a floating installation. [6] Hardwood Floor
Check the flatness of the subfloor. Use a straight piece of lumber that is between 8 and 10 feet in length to find any areas of the subfloor that aren't level. Simply lay down the plank and look for dips beneath it or raised humps. Mark any problem spots you find. Move the plank across the floor 1 way, then turn it diagonally and go across the surface again.[6] Denver Hardwood Floor Install
As the name suggests, solid hardwood is a single, solid piece of wood. Its natural simplicity has made it a popular flooring choice for generations, but that same simplicity makes it less than ideal for modern homes. Wood is a naturally porous material, meaning it is soft, extremely prone to denting, and absorbs water like a sponge. All of these attributes are ideal for helping trees grow, but they don’t translate well to modern flooring. Floors today need to withstand heavy traffic, drops, scratches, and most importantly, spills.
Warranty & Brand – The value of your floor extends well beyond the floor itself. The people that created, tested, produced, and support it are just as important to consider. You want to make sure you are buying a floor from a manufacturer who you can trust. What kind of testing are they doing to make sure the floor you are buying will last? How can they help you if problems do occur down the road? What does the warranty actually cover? These are important factors to consider, especially when hardwood flooring doesn’t meet Rigid Core flooring’s abilities in areas like durability, dent resistance, and waterproofing. Hardwood Floor
×