A hardwood flooring installation takes time, precision, and know-how to get it right. Even for experienced DIYers, hardwood installations can be challenging. A lot depends on your ability to take the time to learn what you need to know to properly install a hardwood floor, so that it will look and perform beautifully. If you've never installed hardwood you will find it worthwhile to hire a professional installer.
Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4).
No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Denver Hardwood Flooring
My advice is to bring in a professional to make sure the floors can be refinished (i.e. if there is still enough room/if you didn’t permanently damage the wood), and if so, have them refinish them rather than replace them – that will be much less expensive. I don’t know where you live and the going rates, but in our area, it’s prob. the price is prob. $1-2 lower…but that may be par for your area. Call in 2-3 people to see. I would check Angie’s List (angieslist.com) for some good local people in your area. Denver Hardwood Flooring
Generally, hardwood floors need to be buffed every 3–5 years. The process usually takes about one day. Buffing refers to the process of using a stand up floor buffer. The floor is abraded with 180 grit screen on the buffer. This allows for the new coat of finish to mechanically adhere to the floor. This process works with great results as long as the floor hasn't had any waxes or synthetic cleaners.
Hardwood can match any décor, from traditional light wood floors to trendy white wood flooring, grey wood floors and dark wood floors. Start with unfinished hard wood flooring boards to create a blank canvas for stain and unique design. We also have hand-scraped hardwood and distressed wood flooring to add a rustic, timeworn look. A wide plank wood flooring can also make a room feel bigger and more modern. Hardwood flooring also has DIY installation that’s easy with tongue and groove flooring options.
Enhance your home with beautiful hardwood flooring that Enhance your home with beautiful hardwood flooring that fits your budget. Full of abundant character and color variation the Bruce Plano collection celebrates the beauty of natural hardwood. Enjoy natural features including mineral streaks knots and small holes and minor milling imperfections. Design your floor to your unique tastes with ... More + Product Details Close Denver Hardwood Floor Install
Although hardwood floors are amazingly beautiful and durable, they are not indestructible. The best floor maintenance plan for hardwood floors include regular vacuuming or sweeping with a soft bristle broom, especially in high traffic areas. Removing dirt or grit from your floors will reduce scratches. Vacuums with rotary brush heads can also scratch your floors. Denver Hardwood Flooring
This has to be the most disappointing show I've seen. This is not respecting anything about the old house. This is tear it all apart and build new. Blah. Boooooo! Bah humbug! Respect the past. Be creative in melding the old and new. Very disappointed in the owners, the designer, and especially the old house staff - including in the first episode where Kevin was basically laughing at the old knotty pine originals. Denver Hardwood Flooring
Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage. Denver Hardwood Floor
Wood flooring can also be installed utilizing the glue-down method. This is an especially popular method for solid parquet flooring installations on concrete sub-floors. Additionally, engineered wood flooring may use the glue-down method as well. A layer of mastic is placed onto the sub-floor using a trowel similar to those used in laying ceramic tile. The wood pieces are then laid on top of the glue and hammered into place using a rubber mallet and a protected 2x4 to create a level floor. Often the parquet floor will require sanding and re-finishing after the glue-down installation method due to the small size pieces. Denver Hardwood Floor Install
Judy – I’m sorry to hear this. I am surprised, but it does happen once in a while. I would probably get a 2nd opinion just to make sure. If they were solid hardwood and are now too thin, then it sounds like they’ve been refinished many times. Generally solid hardwood flooring is 3/4″ thick and that is what you should get if you put in anything new. That will then last a long time and you won’t have this issue in the future.
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor. It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Denver Hardwood Flooring
Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage. Hardwood Floor