Rigid Core flooring is a category of resilient flooring, and it has been designed from the ground up with modern homes in mind. It’s 100% waterproof, easy to install, and provides extreme scratch and indent resistance when compared to solid or engineered wood flooring. It also offers a wide range of design options because it isn’t limited to traditional wood species. Its hybrid visuals, exotic species, colors, and textures go above and beyond anything traditional wood flooring can offer. Denver Hardwood Floor


– If you want less mess and shorter installation, replacing the floors will usually take less time than refinishing them. Refinishing hardwood floors is messy and time consuming. It’s especially challenging if you are already living in the home and have furniture everywhere. Refinishing you hardwood floors can easily take 4-5 days and during that time you can not have furniture on them nor walk on them. For some homes, this creates logistical nightmares as they can’t stay in the home nor would they want to given the smell and the mess. Alternatively, if you replace the floors with prefinished hardwood, it’s a much faster process, less messy and you can still live in the home fairly easily. I have many customers that have done this simply because they want to avoid the mess created from refinishing the hardwood floors. Denver Hardwood Floor
A hardwood flooring installation takes time, precision, and know-how to get it right. Even for experienced DIYers, hardwood installations can be challenging. A lot depends on your ability to take the time to learn what you need to know to properly install a hardwood floor, so that it will look and perform beautifully. If you've never installed hardwood you will find it worthwhile to hire a professional installer.

Engineered wood flooring consists of two or more layers of wood adhered together to form a plank. Typically, engineered wood flooring uses a thin layer (lamella) of a more expensive wood bonded to a core constructed from cheaper wood. The increased stability of engineered wood is achieved by running each layer at a 90° angle to the layer above. This stability makes it a universal product that can be installed over all types of subfloors above, below or on grade. Engineered wood is the most common type of wood flooring in Europe and has been growing in popularity in North America[4]. Denver Hardwood Flooring
A number of proprietary features for solid wood floors are available. Many solid woods come with grooves cut into the back of the wood that run the length of each plank, often called 'absorption strips,' that are intended to reduce cupping. Solid wood floors are mostly manufactured 0.75 inches (19 mm) thick with a tongue-and-groove for installation. Denver Hardwood Floor
As you’re shopping for floor covering, make notes on the price of the materials. The most common types of flooring material include carpeting, vinyl and linoleum flooring, natural stone flooring, solid hardwood, engineered stone flooring and laminate flooring. They range in cost from less than $2 per square foot for cheap vinyl, ceramic tile and carpet to over $8 per square foot for exotic wood and natural stone flooring. Denver Hardwood Floor
Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”. Hardwood Floor
– If you want to change the species of wood, you may consider replacing the hardwood. The majority of homes in the US have oak. Some people love the look and graining of oak; other customers prefer a more unique look – such as a brilliant Brazilian cherry or a clear maple or a modern looking bamboo. If this is the type of look you are going for, changing woods may make sense for you. But, please understand that you can stain your current floors a different color than they are now. So, don’t just make a change because you don’t like the color since that is easily changeable.
We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor.
Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps:
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Floor Install
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store.

– If your floors are REALLY OLD and have been refinished many times, it may be time for a new floor. I’m not talking about oak floors that have been dinged and scratched up…I mean if your floors have been down for over 100 yrs and refinished at least 5 times. If you can see the “tongue” where the boards fit together, it’s probably time for a new floor. Or, if your floors are rather bouncy and/or don’t seem very sturdy, it’s time for a new floor. This happens more often with pine floors as pine floors are softer and used a long time ago.

Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Hardwood Floor
Although many people speak about hardwood floors as a single building material, it’s important to understand that they can be made from dozens of different tree varieties, and each has a different color, price and durability. Here are a few of the most popular hardwood flooring options, along with some unique characteristics of each and average pricing: Denver Hardwood Flooring
We live in a 1924 home with very heavy thick oak woodwork thru out. It also has oak floors, quarter sawn in narrow strips, that In most rooms are in need of refinishing. We had a professional come & take a look yesterday, she said the flooring is too thin to sand & refinish. I was shocked, the floors have never been refinished. I was so disappointed. What can be done, if anything? We also have extended our kitchen & wanted to put oak flooring down to match the rest of the house. She said they don’t make this thickness anymore & the new flooring would be much thicker, therefore making it higher than the dining room that opens to it. Hardwood Floor
×