Over the years, many hardwood floors develop small splits or cracks in the surface of the wood. These can be spot repaired with some angled nails to secure the two pieces together, along with some wood putty to hide the blemishes. If your floor is suffering from large cracks, however, you might want to think about refinishing the floor. And if the split is particularly bad, you should probably replace the damaged plank altogether. Denver Hardwood Floor Install
I love it! I actually have an entire wall dedicated to most of my hand tools. And I want to build a miter station along one wall at some point. I’m tempted to add a bunch of drawers for a clean look and to keep dust travel off of shelves, but I have a serious “out of sight, out of mind” mentality. I think I’m going with shelves and a few drawers as a compromise. Outstanding workmanship!
This has to be the most disappointing show I've seen. This is not respecting anything about the old house. This is tear it all apart and build new. Blah. Boooooo! Bah humbug! Respect the past. Be creative in melding the old and new. Very disappointed in the owners, the designer, and especially the old house staff - including in the first episode where Kevin was basically laughing at the old knotty pine originals.
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Floor
There are some characteristics that are common to each category: solid wood is more frequently site-finished, is always in a plank format, is generally thicker than engineered wood, and is usually installed by nailing. Engineered wood is more frequently pre-finished, has bevelled edges, is very rarely site-finished, and is installed with glue or as a floating installation. [6] Hardwood Floor
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11] Denver Hardwood Flooring
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs. Denver Hardwood Flooring
Generally, hardwood floors need to be buffed every 3–5 years. The process usually takes about one day. Buffing refers to the process of using a stand up floor buffer. The floor is abraded with 180 grit screen on the buffer. This allows for the new coat of finish to mechanically adhere to the floor. This process works with great results as long as the floor hasn't had any waxes or synthetic cleaners.
You cannot restore every wood floor by simply refinishing it. If your wood floor has become warped or if several of the planks have become damaged, you will typically need to replace the entire floor, as finishing will only brighten an already-damaged surface. On really old floors, you may see the tongue where the boards come together, or your boards may lack adequate thickness. Floors like this are definite candidates for replacement, as refinishing is purely cosmetic. Hardwood Floor
Refinishing can actually take much more time than fully replacing a wood floor. Refinishing is a messy, meticulous process than can take approximately four to five days, during which the floor surface must remain completely untouched. The process requires sanders, edgers, buffers, scrapers, brushes, base coat sealers, topcoat sealers, putty knives and sometimes paint. Replacement, on the other hand, can be done in considerably less time using only lumber, a couple of saws, measuring tape, a flat bar, a chalk line and a nail gun.
My advice is to bring in a professional to make sure the floors can be refinished (i.e. if there is still enough room/if you didn’t permanently damage the wood), and if so, have them refinish them rather than replace them – that will be much less expensive. I don’t know where you live and the going rates, but in our area, it’s prob. the price is prob. $1-2 lower…but that may be par for your area. Call in 2-3 people to see. I would check Angie’s List (angieslist.com) for some good local people in your area. Denver Hardwood Floor Install
If you’re thinking about redoing your hardwood floor, you might envision a refreshed look to your kitchen or hallway. You can picture your friends coming to your home for your next party and admiring your new floor, but you may find something standing in the way — you have no idea which type of hardwood flooring to get. With some research on your end, you can save yourself time and money. Let’s explore the features of some popular hardwood flooring types. Denver Hardwood Floor

You cannot restore every wood floor by simply refinishing it. If your wood floor has become warped or if several of the planks have become damaged, you will typically need to replace the entire floor, as finishing will only brighten an already-damaged surface. On really old floors, you may see the tongue where the boards come together, or your boards may lack adequate thickness. Floors like this are definite candidates for replacement, as refinishing is purely cosmetic. Hardwood Floor

No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Denver Hardwood Flooring

Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise. Denver Hardwood Flooring


This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Hardwood Floor
×