Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Hardwood Floor
Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Denver Hardwood Floor
Judy – I’m sorry to hear this. I am surprised, but it does happen once in a while. I would probably get a 2nd opinion just to make sure. If they were solid hardwood and are now too thin, then it sounds like they’ve been refinished many times. Generally solid hardwood flooring is 3/4″ thick and that is what you should get if you put in anything new. That will then last a long time and you won’t have this issue in the future. Denver Hardwood Floor
Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage. Denver Hardwood Floor Install

Add style, warmth, and value to your home with beautiful hardwood floors from The Home Depot. Our hardwood floors are available in solid and engineered hardwood, and a wide variety of colors, styles and wood species. Whether you’re interested in a traditional look, like a classic oak wood floor or something more modern and contemporary, like bamboo floors or cork flooring, we have everything you need to get your flooring project done.
Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”. Denver Hardwood Floor
This has to be the most disappointing show I've seen. This is not respecting anything about the old house. This is tear it all apart and build new. Blah. Boooooo! Bah humbug! Respect the past. Be creative in melding the old and new. Very disappointed in the owners, the designer, and especially the old house staff - including in the first episode where Kevin was basically laughing at the old knotty pine originals.
Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Hardwood Floor
Warped hardwood floors, also known as sagging, is a serious problem for any homeowner. It is often the result of serious moisture problems, and any evidence of warped hardwood floors needs to be addressed immediately. Warped hardwood floors are rarely the result of faulty hardwood or installation, but are a symptom of larger moisture problems in the home itself that need to be taken care of.
Generally, hardwood floors need to be buffed every 3–5 years. The process usually takes about one day. Buffing refers to the process of using a stand up floor buffer. The floor is abraded with 180 grit screen on the buffer. This allows for the new coat of finish to mechanically adhere to the floor. This process works with great results as long as the floor hasn't had any waxes or synthetic cleaners. Hardwood Floor

No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Denver Hardwood Flooring
Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you! Denver Hardwood Floor
Local Retailers: Local home improvement stores often carry a number of engineered wood flooring products in stock. Additionally, local flooring stores can provide samples that let you see how the color and style of the engineered floor will look in your home. Either option may offer you an on-site estimate to give you a better idea about what your project could cost. Hardwood Floor
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank.
With the extensive number of wood flooring options available, ranging from traditional hardwood to engineered hardwood floors, you must do your research to find the right option for your home. Additionally, installation can be a big job and it’s one that most homeowners need to hire professionals to complete. Use this cost guide to get a better understanding of the various expenses associated with installing hardwood floors in your home. Denver Hardwood Flooring
To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Denver Hardwood Floor
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3]
Rigid Core flooring is a category of resilient flooring, and it has been designed from the ground up with modern homes in mind. It’s 100% waterproof, easy to install, and provides extreme scratch and indent resistance when compared to solid or engineered wood flooring. It also offers a wide range of design options because it isn’t limited to traditional wood species. Its hybrid visuals, exotic species, colors, and textures go above and beyond anything traditional wood flooring can offer. Denver Hardwood Floor
Rigid Core flooring is a category of resilient flooring, and it has been designed from the ground up with modern homes in mind. It’s 100% waterproof, easy to install, and provides extreme scratch and indent resistance when compared to solid or engineered wood flooring. It also offers a wide range of design options because it isn’t limited to traditional wood species. Its hybrid visuals, exotic species, colors, and textures go above and beyond anything traditional wood flooring can offer. Hardwood Floor
Michael – The exotic woods are a bit more challenging to work with stain wise because they are naturally darker and redder. Yes, you can refinish them and make them darker and browner. But, you will still have some underlying red tones. So, you may need to go darker than what you’re thinking to drown out the red more. Definitely test colors. Most likely, dark walnut will come out the darkest. Use duraseal…it’s a better stain, dries faster and is a bit darker than minwax. Hardwood Floor

Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs.
Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Hardwood Floor

If you’re thinking about redoing your hardwood floor, you might envision a refreshed look to your kitchen or hallway. You can picture your friends coming to your home for your next party and admiring your new floor, but you may find something standing in the way — you have no idea which type of hardwood flooring to get. With some research on your end, you can save yourself time and money. Let’s explore the features of some popular hardwood flooring types.

My advice is to bring in a professional to make sure the floors can be refinished (i.e. if there is still enough room/if you didn’t permanently damage the wood), and if so, have them refinish them rather than replace them – that will be much less expensive. I don’t know where you live and the going rates, but in our area, it’s prob. the price is prob. $1-2 lower…but that may be par for your area. Call in 2-3 people to see. I would check Angie’s List (angieslist.com) for some good local people in your area. Denver Hardwood Flooring
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs. Denver Hardwood Flooring

Hardwood floors can last a long time, but eventually they need to be replaced. Luckily, it's a pretty straightforward process! Use a circular saw to cut the old hardwood into pieces, then remove the old flooring. Prepare your subflooring so that it's clean and perfectly level. After that, choose your replacement flooring and follow the process for installing that particular type of hardwood! Denver Hardwood Flooring
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Hardwood Floor
×