My advice is to bring in a professional to make sure the floors can be refinished (i.e. if there is still enough room/if you didn’t permanently damage the wood), and if so, have them refinish them rather than replace them – that will be much less expensive. I don’t know where you live and the going rates, but in our area, it’s prob. the price is prob. $1-2 lower…but that may be par for your area. Call in 2-3 people to see. I would check Angie’s List (angieslist.com) for some good local people in your area. Denver Hardwood Flooring
Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Denver Hardwood Floor
If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors.
Local Retailers: Local home improvement stores often carry a number of engineered wood flooring products in stock. Additionally, local flooring stores can provide samples that let you see how the color and style of the engineered floor will look in your home. Either option may offer you an on-site estimate to give you a better idea about what your project could cost.
Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience. Denver Hardwood Flooring
To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Hardwood Floor
Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise.
Awesome explanation! When I say heat pump to people, it's amazing how often their eyes glaze over...even though most of them have had refrigerators and air-conditioners their whole lives and have never asked themselves how they work. Same principle! Compressor and expansion valve (and the heat-holding capacity of a phase change; another confusing one for people). thanks for helping educate!
Over the years, many hardwood floors develop small splits or cracks in the surface of the wood. These can be spot repaired with some angled nails to secure the two pieces together, along with some wood putty to hide the blemishes. If your floor is suffering from large cracks, however, you might want to think about refinishing the floor. And if the split is particularly bad, you should probably replace the damaged plank altogether. Denver Hardwood Flooring
Jasper, Mazama, and the other brands of hardwood flooring we offer are premium quality, delivering everything you want in a hardwood floor - look, strength, durability, and ongoing value for properties. And we offer them to you at incredible pricing not found anywhere else. While we sell discount hardwood flooring, we will never sell cheap hardwood flooring. All of our products undergo rigorous product quality testing before we offer them to you and they are constantly rechecked for quality to ensure you always get the best products while still paying below wholesale prices. Hardwood Floor
Sanding provides a method for smoothing an installed floor, compensating for unevenness of the subfloor. Additionally, sanding is used to renew the appearance of older floors. Sanding using successively finer grades of sandpaper is required to ensure even stain penetration when stains are used, as well as to eliminate visible scratches from coarser sandpaper grades used initially. Prior to modern polyurethanes, oils and waxes were used in addition to stains to provide finishes.[7] Beeswax and linseed oil, for example, are both natural crosslinking polymers and harden over time.[8]
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Denver Hardwood Flooring
Generally, hardwood floors need to be buffed every 3–5 years. The process usually takes about one day. Buffing refers to the process of using a stand up floor buffer. The floor is abraded with 180 grit screen on the buffer. This allows for the new coat of finish to mechanically adhere to the floor. This process works with great results as long as the floor hasn't had any waxes or synthetic cleaners.
You cannot restore every wood floor by simply refinishing it. If your wood floor has become warped or if several of the planks have become damaged, you will typically need to replace the entire floor, as finishing will only brighten an already-damaged surface. On really old floors, you may see the tongue where the boards come together, or your boards may lack adequate thickness. Floors like this are definite candidates for replacement, as refinishing is purely cosmetic.

Engineered wood flooring has other benefits beyond dimensional stability and universal use. Patented installation systems allow for faster installation and easy replacement of boards. Engineered wood also allows for a floating installation where the planks are not adhered to the subfloor or to each other, further increasing ease of repair and reducing installation time. Engineered flooring is also suitable for underfloor and radiant heating systems. Denver Hardwood Floor

Generally, hardwood floors need to be buffed every 3–5 years. The process usually takes about one day. Buffing refers to the process of using a stand up floor buffer. The floor is abraded with 180 grit screen on the buffer. This allows for the new coat of finish to mechanically adhere to the floor. This process works with great results as long as the floor hasn't had any waxes or synthetic cleaners. Hardwood Floor
When it comes to budgeting for this project, you have many factors to consider. Two of the largest considerations include the cost per square foot of the materials and the cost per square foot for installation. To help you understand the potential costs of installing hardwood, we researched the average cost per square foot for traditional and engineered flooring at three different price points. Denver Hardwood Floor
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Denver Hardwood Flooring
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Hardwood Floor

While the overall thickness of flooring is going to vary by category, it is still important to know what is contributing to that thickness. Engineered wood flooring can inflate thickness by adding more layers of plywood or particle board, but still only offer a thin veneer of real wood on top. The dense core allows for Rigid Core floors to be significantly thinner than traditional hardwood floors, with WPC floors being thicker than SPC products. That doesn’t mean all Rigid Core floors are made equally though. Just like how engineered hardwood flooring can inflate thickness, Rigid Core flooring can alter the overall thickness by increasing the size of the acoustical padding on the back. While this padding adds a lot of great features, it doesn’t need to be any thicker than 1mm in size. When it comes to Rigid Core flooring, the thickness of the core is most important. Denver Hardwood Floor Install

Choose your replacement hardwood flooring. You don't have to replace your old floor with the exact same wood or flooring type that you just removed! You can glue your new hardwood flooring into place if you like. You can also install nail-down, floating (or locking) hardwood flooring as a replacement. The choice is up to you and what your budget allows. Denver Hardwood Floor Install
– If your floors are REALLY OLD and have been refinished many times, it may be time for a new floor. I’m not talking about oak floors that have been dinged and scratched up…I mean if your floors have been down for over 100 yrs and refinished at least 5 times. If you can see the “tongue” where the boards fit together, it’s probably time for a new floor. Or, if your floors are rather bouncy and/or don’t seem very sturdy, it’s time for a new floor. This happens more often with pine floors as pine floors are softer and used a long time ago.
No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Denver Hardwood Floor
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs. Denver Hardwood Flooring
Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Hardwood Floor
– If you want to change the species of wood, you may consider replacing the hardwood. The majority of homes in the US have oak. Some people love the look and graining of oak; other customers prefer a more unique look – such as a brilliant Brazilian cherry or a clear maple or a modern looking bamboo. If this is the type of look you are going for, changing woods may make sense for you. But, please understand that you can stain your current floors a different color than they are now. So, don’t just make a change because you don’t like the color since that is easily changeable. Denver Hardwood Floor

Rigid Core flooring is a category of resilient flooring, and it has been designed from the ground up with modern homes in mind. It’s 100% waterproof, easy to install, and provides extreme scratch and indent resistance when compared to solid or engineered wood flooring. It also offers a wide range of design options because it isn’t limited to traditional wood species. Its hybrid visuals, exotic species, colors, and textures go above and beyond anything traditional wood flooring can offer. Hardwood Floor

My advice is to bring in a professional to make sure the floors can be refinished (i.e. if there is still enough room/if you didn’t permanently damage the wood), and if so, have them refinish them rather than replace them – that will be much less expensive. I don’t know where you live and the going rates, but in our area, it’s prob. the price is prob. $1-2 lower…but that may be par for your area. Call in 2-3 people to see. I would check Angie’s List (angieslist.com) for some good local people in your area.
Maple is another great choice for hardwood flooring. Many people prefer its light tan look, which blends into home interior spaces. As one of the strongest woods, maple is a top choice for high-traffic areas of a home. The wood doesn’t scuff easily, making it a good choice for homes with children or those with a lot of foot traffic across the floors. Maple requires minimal maintenance, with weekly sweeping and annual applications of wood soap to prolong the life of the floors. Denver Hardwood Floor
This durable prefinished solid real wood floor will This durable prefinished solid real wood floor will enhance the value of your home. The flooring is made of 3/4 in. thick sawn solid wood and features mother nature's naturally occurring beauty marks such as distinctive color variation knots and mineral streaks. Plank length is totally random and varies based ...  More + Product Details Close Denver Hardwood Floor Install

Most floors use a tongue-and-groove design for connecting adjacent strips. This design makes replacing a single strip or plank challenging, but not impossible. First, look for any nails in the damaged board and drive them as far through the board as possible by using a hammer and nail set. Carpenters use nail sets to drive nails flush with trim without damaging the trim with a hammer. After you’ve cleared the nails, it’s time to remove the damaged board and install a new one. Follow these steps:
Regardless of the floor, the protective finish will play a large role in how scratch and stain resistant it is. Both hardwood and Rigid Core flooring are available with various types of protective finishes. Rigid Core flooring goes a step beyond hardwood though, and also has a transparent solid wear layer that protects against gouging and deeper scratches. Denver Hardwood Flooring
Instead of boiling the hardwood logs, in this process they are kept at a low humidity level and dried slowly to draw moisture from the inside of the wood cells. The logs are then sawn in the same manner as for solid hardwood planks. This style of engineered hardwood has the same look as solid hardwood, and does not have any of the potential problems of "face checking" that rotary-peel and slice-peel products have, because the product is not exposed to added moisture. Denver Hardwood Flooring
Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise. Denver Hardwood Flooring

Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4). Denver Hardwood Floor Install


While the overall thickness of flooring is going to vary by category, it is still important to know what is contributing to that thickness. Engineered wood flooring can inflate thickness by adding more layers of plywood or particle board, but still only offer a thin veneer of real wood on top. The dense core allows for Rigid Core floors to be significantly thinner than traditional hardwood floors, with WPC floors being thicker than SPC products. That doesn’t mean all Rigid Core floors are made equally though. Just like how engineered hardwood flooring can inflate thickness, Rigid Core flooring can alter the overall thickness by increasing the size of the acoustical padding on the back. While this padding adds a lot of great features, it doesn’t need to be any thicker than 1mm in size. When it comes to Rigid Core flooring, the thickness of the core is most important.
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11]

As you’re shopping for floor covering, make notes on the price of the materials. The most common types of flooring material include carpeting, vinyl and linoleum flooring, natural stone flooring, solid hardwood, engineered stone flooring and laminate flooring. They range in cost from less than $2 per square foot for cheap vinyl, ceramic tile and carpet to over $8 per square foot for exotic wood and natural stone flooring.
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs. Denver Hardwood Floor Install

Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage. Hardwood Floor
×