Visual – While hardwood flooring is limited by species and stains, Rigid Core flooring has near limitless options when it comes to flooring that looks like wood. In addition to traditional wood visuals and colors, you can pick from stone looks and even hybrids that marry wood and stones together into unique new options. And best of all you will benefit from a curated look that removes unwanted imperfections like oversized knots, holes, and worming that naturally occurs in hardwood floors. Denver Hardwood Flooring
Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4). Denver Hardwood Floor Install
Like anything, whether you refinish your hardwood floors or replace them depends on your personal circumstances. If you are about to move into a new home, refinishing your hardwood floors is much easier vs. if you already live there. Clearly the cost to refinish the floors Is much less expensive than replacing them (For perspective, to replace them may cost 3-5 times as much). Denver Hardwood Floor Install
With the extensive number of wood flooring options available, ranging from traditional hardwood to engineered hardwood floors, you must do your research to find the right option for your home. Additionally, installation can be a big job and it’s one that most homeowners need to hire professionals to complete. Use this cost guide to get a better understanding of the various expenses associated with installing hardwood floors in your home. Denver Hardwood Flooring
Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience. Denver Hardwood Flooring
Visual – While hardwood flooring is limited by species and stains, Rigid Core flooring has near limitless options when it comes to flooring that looks like wood. In addition to traditional wood visuals and colors, you can pick from stone looks and even hybrids that marry wood and stones together into unique new options. And best of all you will benefit from a curated look that removes unwanted imperfections like oversized knots, holes, and worming that naturally occurs in hardwood floors. Denver Hardwood Floor
Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Hardwood Floor

Another common hardwood floor malady is the development of gaps between planks. The most common causes of gaps between the boards is Mother Nature. Wood shrinks as it dries out, and it expands when it gets wet and humid. That regular expansion and contraction over time is the most common cause of gaps, and is the main reason why most gaps are seasonal in nature. Perhaps your best plan of action is to exercise patience. Denver Hardwood Flooring
Check the flatness of the subfloor. Use a straight piece of lumber that is between 8 and 10 feet in length to find any areas of the subfloor that aren't level. Simply lay down the plank and look for dips beneath it or raised humps. Mark any problem spots you find. Move the plank across the floor 1 way, then turn it diagonally and go across the surface again.[6] Denver Hardwood Floor Install
Besides major problems, you may also experience scratching or loose planks with your hardwood flooring. Scratches can be repaired with touch up kits, or something as simple as a like colored crayon. If you’ve got serious scratching, however, you may need to hire a contractor to refinish the flooring altogether. And if you’ve got loose planks, your only solution is to tie them down. Ideally they should be nailed to the subfloor to prevent any more movement, though excessively loose boards can be a sign of improper installation in the first place. Bringing in a professional hardwood installer to re-install your flooring properly is probably the only sure way to permanently solve the problem. Denver Hardwood Floor Install
Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you! Denver Hardwood Floor
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times.[11]
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Floor

Top quality laminate will not match the look and feel of real wood floors. The areas where the planks join will wear considerably over time, and when damage sets in, it is not an easy repair. Laminate is easily damaged by moisture, and when that damage sets in, it cannot be fixed. If the laminate is not laid correctly, it will not be appealing to potential renters or buyers.
Installing hardwood floors can cost between $9 and $12 per square foot, compared with about $3 to $5 per square foot for carpet — so some homeowners opt to install hardwood floors only in some rooms rather than throughout their home. However, carpet typically needs to be replaced if it becomes stained or worn out. Good quality carpet can last about 10 to 15 years, while hardwood floors can last forever.

Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring. Hardwood Floor
– If you want to change the width of the wood or the direction of the hardwood, the only way to do this is to get a new floor. The standard in home is oak 2 ¼” strip. Now, it’s more stylish and more common to get wider planks such as 3 ¼” or 4”or 5” planks. These look more modern and importantly make the room look larger. Another design trick to make the rooms look larger is to lay the planks on a diagonal – that way, it carries your eye along the longest length of the room. Or, you can even get fancy and add borders or do a herringbone pattern. Denver Hardwood Floor
One way you can trim your budget is to buy the wood flooring yourself, pick it up and bring it home so that the installation company only needs to install the flooring. If you want intricate details such as borders or inlaid patterns, you can expect to pay more. Keep the layout simple and you can save $1 to $2 per square foot in extra installation costs. Other ways to keep costs down include:
With the extensive number of wood flooring options available, ranging from traditional hardwood to engineered hardwood floors, you must do your research to find the right option for your home. Additionally, installation can be a big job and it’s one that most homeowners need to hire professionals to complete. Use this cost guide to get a better understanding of the various expenses associated with installing hardwood floors in your home. Denver Hardwood Flooring
– If you want less mess and shorter installation, replacing the floors will usually take less time than refinishing them. Refinishing hardwood floors is messy and time consuming. It’s especially challenging if you are already living in the home and have furniture everywhere. Refinishing you hardwood floors can easily take 4-5 days and during that time you can not have furniture on them nor walk on them. For some homes, this creates logistical nightmares as they can’t stay in the home nor would they want to given the smell and the mess. Alternatively, if you replace the floors with prefinished hardwood, it’s a much faster process, less messy and you can still live in the home fairly easily. I have many customers that have done this simply because they want to avoid the mess created from refinishing the hardwood floors.
Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4). Denver Hardwood Floor
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank. Denver Hardwood Floor Install
As you’re shopping for floor covering, make notes on the price of the materials. The most common types of flooring material include carpeting, vinyl and linoleum flooring, natural stone flooring, solid hardwood, engineered stone flooring and laminate flooring. They range in cost from less than $2 per square foot for cheap vinyl, ceramic tile and carpet to over $8 per square foot for exotic wood and natural stone flooring.
There are some characteristics that are common to each category: solid wood is more frequently site-finished, is always in a plank format, is generally thicker than engineered wood, and is usually installed by nailing. Engineered wood is more frequently pre-finished, has bevelled edges, is very rarely site-finished, and is installed with glue or as a floating installation. [6] Denver Hardwood Floor

No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Hardwood Floor

×