Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4). Denver Hardwood Floor
– If your floors are REALLY OLD and have been refinished many times, it may be time for a new floor. I’m not talking about oak floors that have been dinged and scratched up…I mean if your floors have been down for over 100 yrs and refinished at least 5 times. If you can see the “tongue” where the boards fit together, it’s probably time for a new floor. Or, if your floors are rather bouncy and/or don’t seem very sturdy, it’s time for a new floor. This happens more often with pine floors as pine floors are softer and used a long time ago. Denver Hardwood Floor Install
Choose your replacement hardwood flooring. You don't have to replace your old floor with the exact same wood or flooring type that you just removed! You can glue your new hardwood flooring into place if you like. You can also install nail-down, floating (or locking) hardwood flooring as a replacement. The choice is up to you and what your budget allows. Denver Hardwood Floor Install
If you get a second opinion and they can’t be refinished, then your best option will be replace them…or wait until you can replace them. Given when the house was built I’m doubting the floors are even, so putting a floating on top will be a really bad option as they will wobble. And, installing wood on top of thin wood is a really bad solution. If your foundation is weak, your floor will be weak and it will creak and separate.
Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”.
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank. Denver Hardwood Flooring
One of the best things about cork floors is that they are environmentally friendly because cork is a sustainable and renewable resource. The natural beauty of the material can suite any decor. The structure of the cork allows for a natural comfort and softness to absorb shock. This is why use of cork flooring is a good application in areas where people will be on their feet for extended periods of time. Using cork floors will reduce noise from traffic or dropping items, also because of the structure of the cork material. The natural properties of the material make it healthy because it is not only resistant to insects, but it is hypo-allergenic. Denver Hardwood Flooring
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7] Hardwood Floor
×