To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Hardwood Floor
Over the years, many hardwood floors develop small splits or cracks in the surface of the wood. These can be spot repaired with some angled nails to secure the two pieces together, along with some wood putty to hide the blemishes. If your floor is suffering from large cracks, however, you might want to think about refinishing the floor. And if the split is particularly bad, you should probably replace the damaged plank altogether. Denver Hardwood Flooring
Choosing teak for your hardwood floors can be a smart choice. You’ll find teak is resistant to pests, as the natural oils found in the wood are undesirable to most insects, including termites. Teak is also a water-resistant wood choice, a bonus if you have young, active children or pets that come indoors soaking wet after walks in the rain. Teak bears an attractive reddish-brown color. However, if left untreated, teak can turn a silver color if exposed to UV rays of sunlight. To prevent discoloration and wear, you can treat the wood with a coating of oil to seal it so that you can enjoy beautiful teak floors for years to come. Denver Hardwood Floor
Warranty & Brand – The value of your floor extends well beyond the floor itself. The people that created, tested, produced, and support it are just as important to consider. You want to make sure you are buying a floor from a manufacturer who you can trust. What kind of testing are they doing to make sure the floor you are buying will last? How can they help you if problems do occur down the road? What does the warranty actually cover? These are important factors to consider, especially when hardwood flooring doesn’t meet Rigid Core flooring’s abilities in areas like durability, dent resistance, and waterproofing. Denver Hardwood Flooring
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Floor
There are some characteristics that are common to each category: solid wood is more frequently site-finished, is always in a plank format, is generally thicker than engineered wood, and is usually installed by nailing. Engineered wood is more frequently pre-finished, has bevelled edges, is very rarely site-finished, and is installed with glue or as a floating installation. [6] Hardwood Floor
Local Retailers: Local home improvement stores often carry a number of engineered wood flooring products in stock. Additionally, local flooring stores can provide samples that let you see how the color and style of the engineered floor will look in your home. Either option may offer you an on-site estimate to give you a better idea about what your project could cost. Denver Hardwood Flooring
With their increased durability and moisture resistance, engineered wood floors are a better option than traditional hardwoods if you have pets or spill-prone kids. Additionally, you can install engineered wood flooring in places that hardwoods typically can't go, including basements, kitchens and summer homes in high-humidity climates. This type of flooring is available in a variety of widths, colors and styles, including glue-down and floating floors.
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation.
No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Denver Hardwood Floor
When it comes to choosing the perfect flooring for a home, hardwood is often the first choice for many homeowners. While it is far from the cheapest option on the market, with the average homeowner spending about $4,396 to install wood floors, it’s popular for its classic and warm appearance, durability and versatility. They can add value to your home when it comes time to sell, and this material can make any space look more appealing. Denver Hardwood Flooring
Check the flatness of the subfloor. Use a straight piece of lumber that is between 8 and 10 feet in length to find any areas of the subfloor that aren't level. Simply lay down the plank and look for dips beneath it or raised humps. Mark any problem spots you find. Move the plank across the floor 1 way, then turn it diagonally and go across the surface again.[6]
Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you! Denver Hardwood Floor

Regardless of the floor, the protective finish will play a large role in how scratch and stain resistant it is. Both hardwood and Rigid Core flooring are available with various types of protective finishes. Rigid Core flooring goes a step beyond hardwood though, and also has a transparent solid wear layer that protects against gouging and deeper scratches. Denver Hardwood Flooring


Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4).
This has to be the most disappointing show I've seen. This is not respecting anything about the old house. This is tear it all apart and build new. Blah. Boooooo! Bah humbug! Respect the past. Be creative in melding the old and new. Very disappointed in the owners, the designer, and especially the old house staff - including in the first episode where Kevin was basically laughing at the old knotty pine originals.

 Acacia (9)  American Walnut (1)  Ash (5)  Bamboo (22)  Beech (5)  Birch (3)  Bloodwood (2)  Brazilian Cherry (10)  Brazilian Chestnut (5)  Brazilian Koa (9)  Brazilian Oak (5)  Brazilian Walnut (5)  Cumaru (3)  Curupay (2)  Hevea (4)  Hickory (27)  Maple (14)  Oak (15)  Pecan (3)  Pine (10)  Purple Heart (2)  Red Cumaru (2)  Red Maple (1)  Red Oak (40)  Short Leaf Acacia (3)  ShortLeaf Acacia (1)  Spanish Hickory (3)  Tamboril (2)  Tauari (3)  Walnut (1)  White Oak (34)
If you get a second opinion and they can’t be refinished, then your best option will be replace them…or wait until you can replace them. Given when the house was built I’m doubting the floors are even, so putting a floating on top will be a really bad option as they will wobble. And, installing wood on top of thin wood is a really bad solution. If your foundation is weak, your floor will be weak and it will creak and separate. Denver Hardwood Floor Install
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Hardwood Floor

A buckled floor happens when the boards warp and lift up from the subfloor that they are attached to. You’ll most likely need to call in a hardwood floor installer to identify the root of the problem if buckling is an issue. Once the cause of your buckling has been identified, you’ll need to take the necessary measures to ensure that your hardwood planks are firmly attached to the subfloor so that the problem no longer persists.
– If you want to change the species of wood, you may consider replacing the hardwood. The majority of homes in the US have oak. Some people love the look and graining of oak; other customers prefer a more unique look – such as a brilliant Brazilian cherry or a clear maple or a modern looking bamboo. If this is the type of look you are going for, changing woods may make sense for you. But, please understand that you can stain your current floors a different color than they are now. So, don’t just make a change because you don’t like the color since that is easily changeable. Denver Hardwood Floor
No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Denver Hardwood Floor
Put on gloves, knee pads, and protective eye glasses. You'll be working diligently on your hands and knees for hours to complete this project, especially if you're doing a large space. Invest in a good pair of knee pads to protect your knees. Sturdy work gloves will protect your hands from splinters, and goggles will prevent sawdust and other debris from getting into your eyes.[1] Denver Hardwood Floor
– If your floors are REALLY OLD and have been refinished many times, it may be time for a new floor. I’m not talking about oak floors that have been dinged and scratched up…I mean if your floors have been down for over 100 yrs and refinished at least 5 times. If you can see the “tongue” where the boards fit together, it’s probably time for a new floor. Or, if your floors are rather bouncy and/or don’t seem very sturdy, it’s time for a new floor. This happens more often with pine floors as pine floors are softer and used a long time ago. Denver Hardwood Floor Install
Hardwood can match any décor, from traditional light wood floors to trendy white wood flooring, grey wood floors and dark wood floors. Start with unfinished hard wood flooring boards to create a blank canvas for stain and unique design. We also have hand-scraped hardwood and distressed wood flooring to add a rustic, timeworn look. A wide plank wood flooring can also make a room feel bigger and more modern. Hardwood flooring also has DIY installation that’s easy with tongue and groove flooring options. Denver Hardwood Floor
Top quality laminate will not match the look and feel of real wood floors. The areas where the planks join will wear considerably over time, and when damage sets in, it is not an easy repair. Laminate is easily damaged by moisture, and when that damage sets in, it cannot be fixed. If the laminate is not laid correctly, it will not be appealing to potential renters or buyers.
You cannot restore every wood floor by simply refinishing it. If your wood floor has become warped or if several of the planks have become damaged, you will typically need to replace the entire floor, as finishing will only brighten an already-damaged surface. On really old floors, you may see the tongue where the boards come together, or your boards may lack adequate thickness. Floors like this are definite candidates for replacement, as refinishing is purely cosmetic. Denver Hardwood Floor
When it comes to budgeting for this project, you have many factors to consider. Two of the largest considerations include the cost per square foot of the materials and the cost per square foot for installation. To help you understand the potential costs of installing hardwood, we researched the average cost per square foot for traditional and engineered flooring at three different price points. Hardwood Floor
×