Check the flatness of the subfloor. Use a straight piece of lumber that is between 8 and 10 feet in length to find any areas of the subfloor that aren't level. Simply lay down the plank and look for dips beneath it or raised humps. Mark any problem spots you find. Move the plank across the floor 1 way, then turn it diagonally and go across the surface again.[6] Denver Hardwood Floor Install
First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional.
To fix a buckled floorboard, you need to be able to access the floor from below. The way to tackle this problem is to put weight on the buckled area from above — a cement block works well. Then install a 1 1/4-inch screw in the buckled flooring from below. Allow the screw to penetrate only halfway into the flooring, or it may come up through the finished surface. Driving the screw through the subfloor and into the flooring pulls the flooring down against the subfloor and gets rid of the buckled spot. Denver Hardwood Floor
Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Hardwood Floor
– If you want to change the width of the wood or the direction of the hardwood, the only way to do this is to get a new floor. The standard in home is oak 2 ¼” strip. Now, it’s more stylish and more common to get wider planks such as 3 ¼” or 4”or 5” planks. These look more modern and importantly make the room look larger. Another design trick to make the rooms look larger is to lay the planks on a diagonal – that way, it carries your eye along the longest length of the room. Or, you can even get fancy and add borders or do a herringbone pattern. Denver Hardwood Flooring
This has to be the most disappointing show I've seen. This is not respecting anything about the old house. This is tear it all apart and build new. Blah. Boooooo! Bah humbug! Respect the past. Be creative in melding the old and new. Very disappointed in the owners, the designer, and especially the old house staff - including in the first episode where Kevin was basically laughing at the old knotty pine originals. Denver Hardwood Flooring
 116% harder than Red Oak (1)  12% harder than Red Oak (11)  123% Harder than Red Oak (4)  125% harder than Red Oak (2)  141% harder than Red Oak (2)  15% softer than Red Oak (2)  165% harder than Red Oak (2)  174% harder than Red Oak (5)  18% softer than Red Oak (1)  185% harder than Red Oak (4)  198 % harder than Red Oak (2)  2% harder than Red Oak (2)  2% Softer than Red Oak (1)  25% softer than Red Oak (1)  28% harder than Red Oak (1)  30% harder than Red Oak (8)  33% harder than Red Oak (2)  41% harder than Red Oak (7)  43% harder than Red Oak (1)  5% harder than Red Oak (8)  53% softer than Red Oak (1)  6% harder than Red Oak (14)  67% harder than Red Oak (5)  74% harder than Red Oak (2)  81% harder than Red Oak (2)  82% harder than Red Oak (2)  9% softer than Red Oak (1)  about the same as Red Oak (7)  Benchmark at 1290 on Janka Scale (37)
Visual – While hardwood flooring is limited by species and stains, Rigid Core flooring has near limitless options when it comes to flooring that looks like wood. In addition to traditional wood visuals and colors, you can pick from stone looks and even hybrids that marry wood and stones together into unique new options. And best of all you will benefit from a curated look that removes unwanted imperfections like oversized knots, holes, and worming that naturally occurs in hardwood floors. Denver Hardwood Flooring
Jasper, Mazama, and the other brands of hardwood flooring we offer are premium quality, delivering everything you want in a hardwood floor - look, strength, durability, and ongoing value for properties. And we offer them to you at incredible pricing not found anywhere else. While we sell discount hardwood flooring, we will never sell cheap hardwood flooring. All of our products undergo rigorous product quality testing before we offer them to you and they are constantly rechecked for quality to ensure you always get the best products while still paying below wholesale prices. Hardwood Floor
The natural process of things will tend to close gaps as the weather and humidity changes. As a rule, if the gap is less than the thickness of a dime, your flooring is normal and there’s nothing to worry about. If your gaps are more persistent, you might need to call in a professional to tighten up your hardwood floor so that they cease to be a problem. Denver Hardwood Floor Install
Wood flooring can also be installed utilizing the glue-down method. This is an especially popular method for solid parquet flooring installations on concrete sub-floors. Additionally, engineered wood flooring may use the glue-down method as well. A layer of mastic is placed onto the sub-floor using a trowel similar to those used in laying ceramic tile. The wood pieces are then laid on top of the glue and hammered into place using a rubber mallet and a protected 2x4 to create a level floor. Often the parquet floor will require sanding and re-finishing after the glue-down installation method due to the small size pieces. Denver Hardwood Floor Install
Engineered wood flooring was created to lower the cost of wood flooring and attempt to fix some of solid wood’s shortcomings. It’s constructed from inexpensive plywood or particle board and topped with a thin veneer of hardwood. This construction helps with installation flexibility and slightly improves indent performance, but it adds a new set of problems as well. Because the “real” wood part of the floor is just a thin veneer, damage from scratches can be irreparable. Engineered wood floors are still made from porous wood, meaning they can’t be subjected to water. Denver Hardwood Floor
Sanding provides a method for smoothing an installed floor, compensating for unevenness of the subfloor. Additionally, sanding is used to renew the appearance of older floors. Sanding using successively finer grades of sandpaper is required to ensure even stain penetration when stains are used, as well as to eliminate visible scratches from coarser sandpaper grades used initially. Prior to modern polyurethanes, oils and waxes were used in addition to stains to provide finishes.[7] Beeswax and linseed oil, for example, are both natural crosslinking polymers and harden over time.[8]
Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring.
Although hardwood floors are amazingly beautiful and durable, they are not indestructible. The best floor maintenance plan for hardwood floors include regular vacuuming or sweeping with a soft bristle broom, especially in high traffic areas. Removing dirt or grit from your floors will reduce scratches. Vacuums with rotary brush heads can also scratch your floors.
First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional.
Solid hardwood is great for high traffic areas and rooms on the first or second floors where there’s limited moisture. You can purchase your solid hardwood floors either prefinished or unfinished. Prefinished hardwood floors have a coating that protects them and they’re ready to install right out of the box. Unfinished hardwoods allow you to apply your own stain color. Hardwood Floor
×