In general, it will almost ALWAYS be less expensive to refinish your hardwood floors. If you replace them, you need to pay for additional wood as well as ripping up and hauling away existing hardwood. If portions of your hardwood are damaged (e.g. pet stains or minor water stains), you can replace these sections and when you refinish them and it will all look new. Even if you have this, it will still be less expensive then replacing the whole floor.
If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors. Hardwood Floor
Engineered wood flooring consists of two or more layers of wood adhered together to form a plank. Typically, engineered wood flooring uses a thin layer (lamella) of a more expensive wood bonded to a core constructed from cheaper wood. The increased stability of engineered wood is achieved by running each layer at a 90° angle to the layer above. This stability makes it a universal product that can be installed over all types of subfloors above, below or on grade. Engineered wood is the most common type of wood flooring in Europe and has been growing in popularity in North America[4]. Denver Hardwood Flooring
My advice is to bring in a professional to make sure the floors can be refinished (i.e. if there is still enough room/if you didn’t permanently damage the wood), and if so, have them refinish them rather than replace them – that will be much less expensive. I don’t know where you live and the going rates, but in our area, it’s prob. the price is prob. $1-2 lower…but that may be par for your area. Call in 2-3 people to see. I would check Angie’s List (angieslist.com) for some good local people in your area. Denver Hardwood Flooring
– If you want to change the width of the wood or the direction of the hardwood, the only way to do this is to get a new floor. The standard in home is oak 2 ¼” strip. Now, it’s more stylish and more common to get wider planks such as 3 ¼” or 4”or 5” planks. These look more modern and importantly make the room look larger. Another design trick to make the rooms look larger is to lay the planks on a diagonal – that way, it carries your eye along the longest length of the room. Or, you can even get fancy and add borders or do a herringbone pattern. Denver Hardwood Floor
Jasper, Mazama, and the other brands of hardwood flooring we offer are premium quality, delivering everything you want in a hardwood floor - look, strength, durability, and ongoing value for properties. And we offer them to you at incredible pricing not found anywhere else. While we sell discount hardwood flooring, we will never sell cheap hardwood flooring. All of our products undergo rigorous product quality testing before we offer them to you and they are constantly rechecked for quality to ensure you always get the best products while still paying below wholesale prices.
Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs.
With the extensive number of wood flooring options available, ranging from traditional hardwood to engineered hardwood floors, you must do your research to find the right option for your home. Additionally, installation can be a big job and it’s one that most homeowners need to hire professionals to complete. Use this cost guide to get a better understanding of the various expenses associated with installing hardwood floors in your home. Denver Hardwood Flooring
Wood flooring can also be installed utilizing the glue-down method. This is an especially popular method for solid parquet flooring installations on concrete sub-floors. Additionally, engineered wood flooring may use the glue-down method as well. A layer of mastic is placed onto the sub-floor using a trowel similar to those used in laying ceramic tile. The wood pieces are then laid on top of the glue and hammered into place using a rubber mallet and a protected 2x4 to create a level floor. Often the parquet floor will require sanding and re-finishing after the glue-down installation method due to the small size pieces.
 Acacia (9)  American Walnut (1)  Ash (5)  Bamboo (22)  Beech (5)  Birch (3)  Bloodwood (2)  Brazilian Cherry (10)  Brazilian Chestnut (5)  Brazilian Koa (9)  Brazilian Oak (5)  Brazilian Walnut (5)  Cumaru (3)  Curupay (2)  Hevea (4)  Hickory (27)  Maple (14)  Oak (15)  Pecan (3)  Pine (10)  Purple Heart (2)  Red Cumaru (2)  Red Maple (1)  Red Oak (40)  Short Leaf Acacia (3)  ShortLeaf Acacia (1)  Spanish Hickory (3)  Tamboril (2)  Tauari (3)  Walnut (1)  White Oak (34) Hardwood Floor

If you get a second opinion and they can’t be refinished, then your best option will be replace them…or wait until you can replace them. Given when the house was built I’m doubting the floors are even, so putting a floating on top will be a really bad option as they will wobble. And, installing wood on top of thin wood is a really bad solution. If your foundation is weak, your floor will be weak and it will creak and separate. Denver Hardwood Floor Install


Besides major problems, you may also experience scratching or loose planks with your hardwood flooring. Scratches can be repaired with touch up kits, or something as simple as a like colored crayon. If you’ve got serious scratching, however, you may need to hire a contractor to refinish the flooring altogether. And if you’ve got loose planks, your only solution is to tie them down. Ideally they should be nailed to the subfloor to prevent any more movement, though excessively loose boards can be a sign of improper installation in the first place. Bringing in a professional hardwood installer to re-install your flooring properly is probably the only sure way to permanently solve the problem.
Over the years, many hardwood floors develop small splits or cracks in the surface of the wood. These can be spot repaired with some angled nails to secure the two pieces together, along with some wood putty to hide the blemishes. If your floor is suffering from large cracks, however, you might want to think about refinishing the floor. And if the split is particularly bad, you should probably replace the damaged plank altogether. Denver Hardwood Flooring
The age of your floor also plays a role. If your floor has been in place for decades, it may resist refinishing for a number of reasons. For instance, if it has already been refinished several times or if too much of the surface wood has become exposed, refinishing your floor may have little effect. For very old floors, replacement can often be preferable to refinishing. Denver Hardwood Floor Install
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank. Denver Hardwood Flooring
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Floor

Although many people speak about hardwood floors as a single building material, it’s important to understand that they can be made from dozens of different tree varieties, and each has a different color, price and durability. Here are a few of the most popular hardwood flooring options, along with some unique characteristics of each and average pricing:
Like anything, whether you refinish your hardwood floors or replace them depends on your personal circumstances. If you are about to move into a new home, refinishing your hardwood floors is much easier vs. if you already live there. Clearly the cost to refinish the floors Is much less expensive than replacing them (For perspective, to replace them may cost 3-5 times as much). Denver Hardwood Floor Install
We live in a 1924 home with very heavy thick oak woodwork thru out. It also has oak floors, quarter sawn in narrow strips, that In most rooms are in need of refinishing. We had a professional come & take a look yesterday, she said the flooring is too thin to sand & refinish. I was shocked, the floors have never been refinished. I was so disappointed. What can be done, if anything? We also have extended our kitchen & wanted to put oak flooring down to match the rest of the house. She said they don’t make this thickness anymore & the new flooring would be much thicker, therefore making it higher than the dining room that opens to it. Hardwood Floor
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3]
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank. Denver Hardwood Floor
As the name suggests, solid hardwood is a single, solid piece of wood. Its natural simplicity has made it a popular flooring choice for generations, but that same simplicity makes it less than ideal for modern homes. Wood is a naturally porous material, meaning it is soft, extremely prone to denting, and absorbs water like a sponge. All of these attributes are ideal for helping trees grow, but they don’t translate well to modern flooring. Floors today need to withstand heavy traffic, drops, scratches, and most importantly, spills.

Engineered wood flooring was created to lower the cost of wood flooring and attempt to fix some of solid wood’s shortcomings. It’s constructed from inexpensive plywood or particle board and topped with a thin veneer of hardwood. This construction helps with installation flexibility and slightly improves indent performance, but it adds a new set of problems as well. Because the “real” wood part of the floor is just a thin veneer, damage from scratches can be irreparable. Engineered wood floors are still made from porous wood, meaning they can’t be subjected to water. Denver Hardwood Floor
We live in a 1924 home with very heavy thick oak woodwork thru out. It also has oak floors, quarter sawn in narrow strips, that In most rooms are in need of refinishing. We had a professional come & take a look yesterday, she said the flooring is too thin to sand & refinish. I was shocked, the floors have never been refinished. I was so disappointed. What can be done, if anything? We also have extended our kitchen & wanted to put oak flooring down to match the rest of the house. She said they don’t make this thickness anymore & the new flooring would be much thicker, therefore making it higher than the dining room that opens to it. Hardwood Floor
×