Cupped floors, also called washboarding, develops gradually across the width of the wood strip where the edges of the hardwood planks raise up and the center of the board sinks down. The cause of cupped floors is a moisture imbalance where there is more water on the bottom side of the wood plank than on the top. The only cure is to balance the humidity levels in your home, and to give the surface time to return back to normal. After the floor has stabilized, you can have a professional sand it flat and re-finish it to perfection. Denver Hardwood Floor
Warranty & Brand – The value of your floor extends well beyond the floor itself. The people that created, tested, produced, and support it are just as important to consider. You want to make sure you are buying a floor from a manufacturer who you can trust. What kind of testing are they doing to make sure the floor you are buying will last? How can they help you if problems do occur down the road? What does the warranty actually cover? These are important factors to consider, especially when hardwood flooring doesn’t meet Rigid Core flooring’s abilities in areas like durability, dent resistance, and waterproofing. Denver Hardwood Flooring
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Floor
All varieties provide increased durability over traditional wood, but buying engineered wood with more core layers and a thicker veneer offers the most durability. Engineered flooring is available in a wide range of woods, colors and finishes. Here are a few of the most popular engineered flooring options, along with some unique characteristics of each and average pricing: Denver Hardwood Floor

Besides major problems, you may also experience scratching or loose planks with your hardwood flooring. Scratches can be repaired with touch up kits, or something as simple as a like colored crayon. If you’ve got serious scratching, however, you may need to hire a contractor to refinish the flooring altogether. And if you’ve got loose planks, your only solution is to tie them down. Ideally they should be nailed to the subfloor to prevent any more movement, though excessively loose boards can be a sign of improper installation in the first place. Bringing in a professional hardwood installer to re-install your flooring properly is probably the only sure way to permanently solve the problem. Denver Hardwood Floor Install
– If you want to change the species of wood, you may consider replacing the hardwood. The majority of homes in the US have oak. Some people love the look and graining of oak; other customers prefer a more unique look – such as a brilliant Brazilian cherry or a clear maple or a modern looking bamboo. If this is the type of look you are going for, changing woods may make sense for you. But, please understand that you can stain your current floors a different color than they are now. So, don’t just make a change because you don’t like the color since that is easily changeable. Denver Hardwood Floor

The natural process of things will tend to close gaps as the weather and humidity changes. As a rule, if the gap is less than the thickness of a dime, your flooring is normal and there’s nothing to worry about. If your gaps are more persistent, you might need to call in a professional to tighten up your hardwood floor so that they cease to be a problem. Denver Hardwood Floor Install


First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional. Denver Hardwood Flooring
Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage. Denver Hardwood Floor Install
Enhance your home with beautiful hardwood flooring that Enhance your home with beautiful hardwood flooring that fits your budget. Full of abundant character and color variation Bruce Plano Gunstock Oak celebrates the beauty of natural hardwood. Enjoy natural features including mineral streaks knots and small holes and minor milling imperfections. Design your floor to your unique tastes with ...  More + Product Details Close Denver Hardwood Floor
Judy – I’m sorry to hear this. I am surprised, but it does happen once in a while. I would probably get a 2nd opinion just to make sure. If they were solid hardwood and are now too thin, then it sounds like they’ve been refinished many times. Generally solid hardwood flooring is 3/4″ thick and that is what you should get if you put in anything new. That will then last a long time and you won’t have this issue in the future. Denver Hardwood Floor
One of the drawbacks of cork flooring is the cost. It is more expensive than other wood flooring options. The cost of import, plus material, plus installation is more than many budgets can handle. Due to the soft nature of the flooring, it is easily damaged by furniture and shoes, but it can and should be protected just like any other type of wood floor.
Instead of boiling the hardwood logs, in this process they are kept at a low humidity level and dried slowly to draw moisture from the inside of the wood cells. The logs are then sawn in the same manner as for solid hardwood planks. This style of engineered hardwood has the same look as solid hardwood, and does not have any of the potential problems of "face checking" that rotary-peel and slice-peel products have, because the product is not exposed to added moisture. Denver Hardwood Floor Install
Over the years, many hardwood floors develop small splits or cracks in the surface of the wood. These can be spot repaired with some angled nails to secure the two pieces together, along with some wood putty to hide the blemishes. If your floor is suffering from large cracks, however, you might want to think about refinishing the floor. And if the split is particularly bad, you should probably replace the damaged plank altogether. Denver Hardwood Flooring
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Floor Install
Engineered wood flooring has other benefits beyond dimensional stability and universal use. Patented installation systems allow for faster installation and easy replacement of boards. Engineered wood also allows for a floating installation where the planks are not adhered to the subfloor or to each other, further increasing ease of repair and reducing installation time. Engineered flooring is also suitable for underfloor and radiant heating systems.
So, assuming you can’t refinish existing and you can’t afford to replace it now, then focus on the new kitchen and put solid oak there. It’s okay and very common for this to be higher than the rest and it’s easy enough to add a wood transition. And, then later, you will need to replace the existing worn down floors w/ solid oak, so they will eventually be the same height.

No matter which type of flooring you choose, if the subfloor, joists or other structural elements need work, you can expect to pay considerably more in both labor and materials. Plywood for the subflooring averages $22 for each 4-foot by 8-foot sheet. For a 12-foot by 12-foot room, you’d need five sheets of plywood, which increases the cost by $110. Additionally, carpenters often charge $20 to $35 per hour to install new floor joists and subfloors.  For laying a hardwood floor over concrete, it's best to use a floating floor system where the floor is not glued to the concrete.  Wood flooring is a major investment, so always have the concrete checked for moisture prior to installation. Hardwood Floor

Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you! Denver Hardwood Floor
Local Retailers: Local home improvement stores often carry a number of engineered wood flooring products in stock. Additionally, local flooring stores can provide samples that let you see how the color and style of the engineered floor will look in your home. Either option may offer you an on-site estimate to give you a better idea about what your project could cost. Denver Hardwood Floor

When it comes to choosing the perfect flooring for a home, hardwood is often the first choice for many homeowners. While it is far from the cheapest option on the market, with the average homeowner spending about $4,396 to install wood floors, it’s popular for its classic and warm appearance, durability and versatility. They can add value to your home when it comes time to sell, and this material can make any space look more appealing.


The amount you pay for installation depends on a variety of factors, including where you live and the intricacy of your project. For example, furniture removal and replacement, repairing the subfloor and removing and disposing of the old floor all bump up the overall cost of the project more than simply having an installer come in and lay the flooring does. To illustrate, some installers charge 20 cents per square foot for ripping up and removing carpeting or moving furniture. Others may charge a per-appliance fee for moving appliances. Denver Hardwood Flooring
Solid hardwood floors are made of planks milled from a single piece of timber. Solid hardwood floors were originally used for structural purposes, being installed perpendicular to the wooden support beams of a building known as joists or bearers. With the increased use of concrete as a subfloor in some parts of the world, engineered wood flooring has gained some popularity. However, solid wood floors are still common and popular. Solid wood floors have a thicker wear surface and can be sanded and finished more times than an engineered wood floor.[2] It is not uncommon for homes in New England, Eastern Canada, USA, and Europe to have the original solid wood floor still in use today. Hardwood Floor
Choosing teak for your hardwood floors can be a smart choice. You’ll find teak is resistant to pests, as the natural oils found in the wood are undesirable to most insects, including termites. Teak is also a water-resistant wood choice, a bonus if you have young, active children or pets that come indoors soaking wet after walks in the rain. Teak bears an attractive reddish-brown color. However, if left untreated, teak can turn a silver color if exposed to UV rays of sunlight. To prevent discoloration and wear, you can treat the wood with a coating of oil to seal it so that you can enjoy beautiful teak floors for years to come. Hardwood Floor
It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Hardwood Floor
×