It is difficult to compare solid wood flooring to engineered wood flooring due to the wide range of quality in both product categories, particularly engineered. Solid wood has some limitations. Recommended maximum widths and lengths are typically 5" / 127mm wide and 7' / 2100mm long. Solid hardwood is also more prone to "gapping" (excessive space between planks), "crowning" (convex curving upwards when humidity increases) and "cupping" (a concave or "dished" appearance of the plank, with the height of the plank along its longer edges being higher than the centre) with increased plank size. Solid wood cannot be used with underfloor radiant heating.[5] However extra care is necessary with the planning and installation of the heating system and the wood flooring, such as limiting the temperature to 85 °F (29 °C), avoid sharp temperature fluctuations, utilizing an outdoor thermostat to anticipate heating demands, and monitoring the moisture content for the subfloor before installation. Denver Hardwood Floor Install
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Hardwood Floor
Jasper, Mazama, and the other brands of hardwood flooring we offer are premium quality, delivering everything you want in a hardwood floor - look, strength, durability, and ongoing value for properties. And we offer them to you at incredible pricing not found anywhere else. While we sell discount hardwood flooring, we will never sell cheap hardwood flooring. All of our products undergo rigorous product quality testing before we offer them to you and they are constantly rechecked for quality to ensure you always get the best products while still paying below wholesale prices. Denver Hardwood Flooring
Sand off any paint or adhesive on the subfloor (if necessary). How pristine your subfloor needs to be depends on what kind of replacement flooring you're installing. If you plan to glue your new hardwood flooring down, sand away any paint or adhesive stuck to the subfloor with an electric sander. If you're installing nail-down, floating, or locking hardwood, you don't need to sand the subfloor.[5]

Hardwood floors can last a long time, but eventually they need to be replaced. Luckily, it's a pretty straightforward process! Use a circular saw to cut the old hardwood into pieces, then remove the old flooring. Prepare your subflooring so that it's clean and perfectly level. After that, choose your replacement flooring and follow the process for installing that particular type of hardwood! Denver Hardwood Floor
My boyfriend and I recently bought a new house that requires many updates, including floors. The house was built in 1960 and has beautiful original hardwood floors that were covered in carpet. The day we moved in (scratch that: the HOUR we moved in), we pulled up the carpet and had ambitious plans to refinish the floors with a more modern stain. After multiple attempts with rented drum sanders and 12×18 sanders, the floors were just OK. We tried using our own belt sander and palm sander to even out hard to sand areas, particularly the edges, but the end-result was not ideal. We tried our hand at staining anyways because we were fed up with staining (not the greatest idea!). Our floors are unevenly taking the stain and are not up to our standards. Now our question is: do we hire someone to professionally refinish the floors (quotes we have obtained range from $4-5 per square foot) OR replace the floors entirely. Do you have any advice?? Denver Hardwood Flooring
Michael – The exotic woods are a bit more challenging to work with stain wise because they are naturally darker and redder. Yes, you can refinish them and make them darker and browner. But, you will still have some underlying red tones. So, you may need to go darker than what you’re thinking to drown out the red more. Definitely test colors. Most likely, dark walnut will come out the darkest. Use duraseal…it’s a better stain, dries faster and is a bit darker than minwax. Denver Hardwood Floor
Hardwood can match any décor, from traditional light wood floors to trendy white wood flooring, grey wood floors and dark wood floors. Start with unfinished hard wood flooring boards to create a blank canvas for stain and unique design. We also have hand-scraped hardwood and distressed wood flooring to add a rustic, timeworn look. A wide plank wood flooring can also make a room feel bigger and more modern. Hardwood flooring also has DIY installation that’s easy with tongue and groove flooring options.
A number of proprietary features for solid wood floors are available. Many solid woods come with grooves cut into the back of the wood that run the length of each plank, often called 'absorption strips,' that are intended to reduce cupping. Solid wood floors are mostly manufactured 0.75 inches (19 mm) thick with a tongue-and-groove for installation.
My boyfriend and I recently bought a new house that requires many updates, including floors. The house was built in 1960 and has beautiful original hardwood floors that were covered in carpet. The day we moved in (scratch that: the HOUR we moved in), we pulled up the carpet and had ambitious plans to refinish the floors with a more modern stain. After multiple attempts with rented drum sanders and 12×18 sanders, the floors were just OK. We tried using our own belt sander and palm sander to even out hard to sand areas, particularly the edges, but the end-result was not ideal. We tried our hand at staining anyways because we were fed up with staining (not the greatest idea!). Our floors are unevenly taking the stain and are not up to our standards. Now our question is: do we hire someone to professionally refinish the floors (quotes we have obtained range from $4-5 per square foot) OR replace the floors entirely. Do you have any advice??

Choosing teak for your hardwood floors can be a smart choice. You’ll find teak is resistant to pests, as the natural oils found in the wood are undesirable to most insects, including termites. Teak is also a water-resistant wood choice, a bonus if you have young, active children or pets that come indoors soaking wet after walks in the rain. Teak bears an attractive reddish-brown color. However, if left untreated, teak can turn a silver color if exposed to UV rays of sunlight. To prevent discoloration and wear, you can treat the wood with a coating of oil to seal it so that you can enjoy beautiful teak floors for years to come. Denver Hardwood Floor
 116% harder than Red Oak (1)  12% harder than Red Oak (11)  123% Harder than Red Oak (4)  125% harder than Red Oak (2)  141% harder than Red Oak (2)  15% softer than Red Oak (2)  165% harder than Red Oak (2)  174% harder than Red Oak (5)  18% softer than Red Oak (1)  185% harder than Red Oak (4)  198 % harder than Red Oak (2)  2% harder than Red Oak (2)  2% Softer than Red Oak (1)  25% softer than Red Oak (1)  28% harder than Red Oak (1)  30% harder than Red Oak (8)  33% harder than Red Oak (2)  41% harder than Red Oak (7)  43% harder than Red Oak (1)  5% harder than Red Oak (8)  53% softer than Red Oak (1)  6% harder than Red Oak (14)  67% harder than Red Oak (5)  74% harder than Red Oak (2)  81% harder than Red Oak (2)  82% harder than Red Oak (2)  9% softer than Red Oak (1)  about the same as Red Oak (7)  Benchmark at 1290 on Janka Scale (37)
Installing a hardwood floor yourself can save you money – if you know what you’re doing. Improper preparation and installation can lead to warping and buckling, which will ruin flooring that would otherwise remain beautiful for years to come. The most important thing you can do to ensure the structural integrity of your floor is to properly prepare for the installation process. Here are various articles to help you! Denver Hardwood Floor Install
Laminate is a cost effective option that will withstand a certain amount of wear. For an easy installation, opt for click-lock. The planks will snap together and can be laid over other flooring. It is ideal for living areas, and some brands may even construct it with a waterproof core, allowing it to be used in areas where water may be an issue. We suggest taking a close look at the guarantee before installing it in a bathroom. Denver Hardwood Floor Install
Eliminate any problem spots to make the subfloor level. Sand minor humps down with a hand-held or orbital sander to make the subfloor level. To fill any dips or low spots, use a leveling compound (also known as floor patch). Mix up the compound according to package directions, fill in the dips, then pull your straight piece of lumber back and forth over the spot to flatten and level it with the rest of the subfloor.[7]
Floating installation: A floating installation is where the flooring is laid down in a glueless manner on top of a layer of underlay. The individual planks are locked together, and are not glued or nailed down to the subfloor. By doing this the floor is floating above the underlay, and can be laid on top of existing tile or marble, without the risk of damaging the subflooring.
If your only goal is to brighten your floors and restore their original shine, consider refinishing them. But if you want to change some aspect of the floor itself, like the style of the wood, the direction of the planks or the consistency of the material, you will need to invest in a full replacement. Refinishing is ideal to restore existing wood, while replacement is ideal for establishing a completely new look or feel.
We had bought and installed this beautiful product in our downstairs a few years ago. It's now time to do the upstairs and the product was the same excellent value for the price. Arrived quicker than we needed, but gives it time to acclimate to our home. We will be using the same installer and he was happy we are ordering the same product from the same company. He was VERY impressed by the quality of the product last time. I'm excited to see the completed project as I love this wood on our main floor. Denver Hardwood Floor

 Bamboo Flooring (22)  BELLAWOOD (49)  BELLAWOOD Artisan Distressed (13)  BELLAWOOD Artisan Distressed Engineered (4)  BELLAWOOD Engineered (16)  Builders Pride (26)  Builder's Pride (10)  Builder's Pride Engineered (1)  Clover Lea (9)  Major Brand (5)  Mayflower (12)  Mayflower Engineered (19)  R.L. Colston (40)  Virginia Mill Works (8)  Virginia Mill Works Engineered (21) Denver Hardwood Flooring
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Hardwood Floor
×