Hardwood floors can last a long time, but eventually they need to be replaced. Luckily, it's a pretty straightforward process! Use a circular saw to cut the old hardwood into pieces, then remove the old flooring. Prepare your subflooring so that it's clean and perfectly level. After that, choose your replacement flooring and follow the process for installing that particular type of hardwood!
Michael – The exotic woods are a bit more challenging to work with stain wise because they are naturally darker and redder. Yes, you can refinish them and make them darker and browner. But, you will still have some underlying red tones. So, you may need to go darker than what you’re thinking to drown out the red more. Definitely test colors. Most likely, dark walnut will come out the darkest. Use duraseal…it’s a better stain, dries faster and is a bit darker than minwax. Hardwood Floor

The age of your floor also plays a role. If your floor has been in place for decades, it may resist refinishing for a number of reasons. For instance, if it has already been refinished several times or if too much of the surface wood has become exposed, refinishing your floor may have little effect. For very old floors, replacement can often be preferable to refinishing. Denver Hardwood Floor
First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional. Denver Hardwood Floor Install
– If your floors are REALLY OLD and have been refinished many times, it may be time for a new floor. I’m not talking about oak floors that have been dinged and scratched up…I mean if your floors have been down for over 100 yrs and refinished at least 5 times. If you can see the “tongue” where the boards fit together, it’s probably time for a new floor. Or, if your floors are rather bouncy and/or don’t seem very sturdy, it’s time for a new floor. This happens more often with pine floors as pine floors are softer and used a long time ago.
My advice is to bring in a professional to make sure the floors can be refinished (i.e. if there is still enough room/if you didn’t permanently damage the wood), and if so, have them refinish them rather than replace them – that will be much less expensive. I don’t know where you live and the going rates, but in our area, it’s prob. the price is prob. $1-2 lower…but that may be par for your area. Call in 2-3 people to see. I would check Angie’s List (angieslist.com) for some good local people in your area. Denver Hardwood Flooring

With the extensive number of wood flooring options available, ranging from traditional hardwood to engineered hardwood floors, you must do your research to find the right option for your home. Additionally, installation can be a big job and it’s one that most homeowners need to hire professionals to complete. Use this cost guide to get a better understanding of the various expenses associated with installing hardwood floors in your home. Denver Hardwood Flooring


Measure rooms one at a time. It’s easiest to measure rectangles, so if you have an “L-shaped” room, divide it into 2 rectangles and measure them separately. The length of the rectangle multiplied by the width equals the square footage. For example, a room, or section of a room, that is 20 feet long and 12 feet wide produces this formula: 20 x 12 = 240 square feet. If the flooring you are purchasing is sold by the yard, divide the square feet by 9. So, 240 square feet / 9 = 26.667 square yards. Denver Hardwood Floor

A hardwood flooring installation takes time, precision, and know-how to get it right. Even for experienced DIYers, hardwood installations can be challenging. A lot depends on your ability to take the time to learn what you need to know to properly install a hardwood floor, so that it will look and perform beautifully. If you've never installed hardwood you will find it worthwhile to hire a professional installer.


Engineered wood flooring consists of two or more layers of wood adhered together to form a plank. Typically, engineered wood flooring uses a thin layer (lamella) of a more expensive wood bonded to a core constructed from cheaper wood. The increased stability of engineered wood is achieved by running each layer at a 90° angle to the layer above. This stability makes it a universal product that can be installed over all types of subfloors above, below or on grade. Engineered wood is the most common type of wood flooring in Europe and has been growing in popularity in North America[4]. Denver Hardwood Flooring
Because tongue-and-groove boards are locked in place, removal involves cutting out the middle of each damaged board. The easiest way is to bore a 1-in.-dia. hole through both ends of each damaged board (photo 1). Then use a circular saw to connect the two holes (photo 2). Follow these steps to safely make the plunge cuts you need to repair your hardwood floors: 1. Adjust the depth of cut to the thickness of the floorboards. Plug in the saw and put on eye protection. 2. Pull back the retractable blade guard with your thumb. Then hold the nose of the baseplate on the floorboard and lift up the rear of the saw. 3. Align the blade with the right edge of one of the holes. Make sure the blade isn't touching the floor, then squeeze the trigger and slowly lower the spinning blade into the board. 4. Grip the saw firmly with both hands and guide it in a straight line until you cut into the right edge of the hole at the opposite end of the board. 5. Move back to the first hole, align the blade with the left edge and cut to the left edge of the second hole. Pry out the middle section with a hammer and chisel. Chop out the remaining edges, being careful not to damage any surrounding boards (photo 3). The "tongue" piece will be nailed in place, so break it out in small pieces. Then pull out the nails with a hammer or locking pliers. The existing floorboards have a tongue and groove milled on each end and along the edges. Chop off the tongue exposed by the board you just removed so you can slip in the new board (photo 4).
This process begins with the same treatment process that the rotary peel method uses. However, instead of being sliced in a rotary fashion, with this technique the wood is sliced from the log in much the same manner that lumber is sawn from a log – straight through. The veneers do not go through the same manufacturing process as rotary peeled veneers. Engineered hardwood produced this way tends to have fewer problems with "face checking", and also does not have the same plywood appearance in the grain.[3] However, the planks can tend to have edge splintering and cracking because the veneers have been submerged in water and then pressed flat.
Local Retailers: Local home improvement stores often carry a number of engineered wood flooring products in stock. Additionally, local flooring stores can provide samples that let you see how the color and style of the engineered floor will look in your home. Either option may offer you an on-site estimate to give you a better idea about what your project could cost.
Although many people speak about hardwood floors as a single building material, it’s important to understand that they can be made from dozens of different tree varieties, and each has a different color, price and durability. Here are a few of the most popular hardwood flooring options, along with some unique characteristics of each and average pricing:
If you’re thinking about redoing your hardwood floor, you might envision a refreshed look to your kitchen or hallway. You can picture your friends coming to your home for your next party and admiring your new floor, but you may find something standing in the way — you have no idea which type of hardwood flooring to get. With some research on your end, you can save yourself time and money. Let’s explore the features of some popular hardwood flooring types. Denver Hardwood Floor
No matter what type of hardwood flooring you choose, proper care and maintenance will help them look beautiful even longer. First off, don’t let the dirt and dust collect. At least once a week, you’ll want to go over your hardwood floors with a broom or dust mop to pick up any dirt, dust, hair or pet dander. If you’re using a vacuum, make sure it’s set to ‘wood floors’ so that you’re not beating up your floors and damaging them in the process. Denver Hardwood Flooring
If your floors are in need of a deeper cleaning, use a wood floor cleaner. Follow the instructions for diluting the cleaner in water. Clean the floors with a damp mop, going with the grain. Then, go back over the floor with a clean, damp mop to remove any excess cleaner. Finish by drying the floor completely with a dry towel. Remember, leftover standing water could damage your wood floors. Hardwood Floor
With their increased durability and moisture resistance, engineered wood floors are a better option than traditional hardwoods if you have pets or spill-prone kids. Additionally, you can install engineered wood flooring in places that hardwoods typically can't go, including basements, kitchens and summer homes in high-humidity climates. This type of flooring is available in a variety of widths, colors and styles, including glue-down and floating floors. Hardwood Floor
×