If you get a second opinion and they can’t be refinished, then your best option will be replace them…or wait until you can replace them. Given when the house was built I’m doubting the floors are even, so putting a floating on top will be a really bad option as they will wobble. And, installing wood on top of thin wood is a really bad solution. If your foundation is weak, your floor will be weak and it will creak and separate. Hardwood Floor
Engineered wood flooring has other benefits beyond dimensional stability and universal use. Patented installation systems allow for faster installation and easy replacement of boards. Engineered wood also allows for a floating installation where the planks are not adhered to the subfloor or to each other, further increasing ease of repair and reducing installation time. Engineered flooring is also suitable for underfloor and radiant heating systems.
The amount you pay for installation depends on a variety of factors, including where you live and the intricacy of your project. For example, furniture removal and replacement, repairing the subfloor and removing and disposing of the old floor all bump up the overall cost of the project more than simply having an installer come in and lay the flooring does. To illustrate, some installers charge 20 cents per square foot for ripping up and removing carpeting or moving furniture. Others may charge a per-appliance fee for moving appliances.
Instead of boiling the hardwood logs, in this process they are kept at a low humidity level and dried slowly to draw moisture from the inside of the wood cells. The logs are then sawn in the same manner as for solid hardwood planks. This style of engineered hardwood has the same look as solid hardwood, and does not have any of the potential problems of "face checking" that rotary-peel and slice-peel products have, because the product is not exposed to added moisture. Denver Hardwood Floor Install
Choose your replacement hardwood flooring. You don't have to replace your old floor with the exact same wood or flooring type that you just removed! You can glue your new hardwood flooring into place if you like. You can also install nail-down, floating (or locking) hardwood flooring as a replacement. The choice is up to you and what your budget allows.
Solid wood flooring is milled from a single piece of timber that is kiln or air dried before sawing. Depending on the desired look of the floor, the timber can be cut in three ways: flat-sawn, quarter-sawn, and rift-sawn. The timber is cut to the desired dimensions and either packed unfinished for a site-finished installation or finished at the factory. The moisture content at time of manufacturing is carefully controlled to ensure the product does not warp during transport and storage.
First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional. Denver Hardwood Flooring
Glue down engineered hardwood, alternatively. If you don't want to nail down the boards, you do have the option of using adhesive to put engineered hardwood in place. It's a good choice, but won't last as long or be as sturdy as nailed down hardwood. The procedure is very similar to the nail-down process. Follow the adhesive manufacturer's instructions for installation and drying times. Denver Hardwood Floor
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Hardwood Floor
Not only is bamboo resistant to moisture, but it is environmentally friendly and an optimal choice for those who are looking to build “green.” The plant grows faster and does not take as long to re-grow than a typical hardwood tree, therefore not contributing to deforestation. Bamboo flooring is softer than traditional hardwoods, so it will not cause pain if it is stood on for long periods of time. The softness of the floor will also reduce noise. Denver Hardwood Flooring
Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Flooring
Top quality laminate will not match the look and feel of real wood floors. The areas where the planks join will wear considerably over time, and when damage sets in, it is not an easy repair. Laminate is easily damaged by moisture, and when that damage sets in, it cannot be fixed. If the laminate is not laid correctly, it will not be appealing to potential renters or buyers. Hardwood Floor
Tongue-and-groove: One side and one end of the plank have a groove, the other side and end have a tongue (protruding wood along an edge's center). The tongue and groove fit snugly together, thus joining or aligning the planks, and are not visible once joined. Tongue-and-groove flooring can be installed by glue-down (both engineered and solid), floating (mostly engineered only), or nail-down (not recommended for most engineered).
When it comes to budgeting for this project, you have many factors to consider. Two of the largest considerations include the cost per square foot of the materials and the cost per square foot for installation. To help you understand the potential costs of installing hardwood, we researched the average cost per square foot for traditional and engineered flooring at three different price points. Denver Hardwood Floor Install
Width & Length – Plank flooring comes in a variety of widths and lengths. The most common widths are currently in the 5” – 6” range, but wider widths are rapidly becoming more popular. The length of your floor is also important to consider depending on the size of your space. Hardwood flooring comes in mixed lengths because imperfections are cut out of longer planks during production. Rigid Core flooring is built to size and comes in lengths ranging from 36” up to 80+”. Hardwood Floor
A number of proprietary features for solid wood floors are available. Many solid woods come with grooves cut into the back of the wood that run the length of each plank, often called 'absorption strips,' that are intended to reduce cupping. Solid wood floors are mostly manufactured 0.75 inches (19 mm) thick with a tongue-and-groove for installation.
Lowe’s has what you need to bring value-adding beauty to your home with hardwood flooring. There are plenty of species to choose from, including acacia wood flooring, walnut flooring, maple flooring, hickory hardwood flooring and cherry wood flooring. Depending on your budget and room’s traffic level, you’ll be sure to find a style to suit your needs.
Price is the first obvious variable to consider. It is almost always cheaper to refinish your floor than to replace it. When replacing, you must consider the cost of the new wood as well as the installation. You can offset much of this cost by installing the floor yourself, but this is a very invasive process that requires specialized knowledge and precision. You can typically refinish a wood floor yourself, with just a few inexpensive solutions. Denver Hardwood Flooring
This process begins with the same treatment process that the rotary peel method uses. However, instead of being sliced in a rotary fashion, with this technique the wood is sliced from the log in much the same manner that lumber is sawn from a log – straight through. The veneers do not go through the same manufacturing process as rotary peeled veneers. Engineered hardwood produced this way tends to have fewer problems with "face checking", and also does not have the same plywood appearance in the grain. However, the planks can tend to have edge splintering and cracking because the veneers have been submerged in water and then pressed flat. Denver Hardwood Floor Install
Judy – I’m sorry to hear this. I am surprised, but it does happen once in a while. I would probably get a 2nd opinion just to make sure. If they were solid hardwood and are now too thin, then it sounds like they’ve been refinished many times. Generally solid hardwood flooring is 3/4″ thick and that is what you should get if you put in anything new. That will then last a long time and you won’t have this issue in the future. Denver Hardwood Floor Install
If you’re thinking about redoing your hardwood floor, you might envision a refreshed look to your kitchen or hallway. You can picture your friends coming to your home for your next party and admiring your new floor, but you may find something standing in the way — you have no idea which type of hardwood flooring to get. With some research on your end, you can save yourself time and money. Let’s explore the features of some popular hardwood flooring types. Hardwood Floor