I love it! I actually have an entire wall dedicated to most of my hand tools. And I want to build a miter station along one wall at some point. I’m tempted to add a bunch of drawers for a clean look and to keep dust travel off of shelves, but I have a serious “out of sight, out of mind” mentality. I think I’m going with shelves and a few drawers as a compromise. Outstanding workmanship!
Solid hardwood floor planks are made from a piece of wood and made to be anywhere from 18 to 20 mm thick. The boards are made with a tongue and groove to fit together for installation. Depending on the species of wood, certain floors will be harder than others. The harder the floor, the less susceptible it is to dings and scratches. The floor can be sanded and refinished several times to restore its beauty, with the total number of times being determined by the depth of the tongue from the top of the plank. Denver Hardwood Floor

All varieties provide increased durability over traditional wood, but buying engineered wood with more core layers and a thicker veneer offers the most durability. Engineered flooring is available in a wide range of woods, colors and finishes. Here are a few of the most popular engineered flooring options, along with some unique characteristics of each and average pricing: Denver Hardwood Floor
If you get a second opinion and they can’t be refinished, then your best option will be replace them…or wait until you can replace them. Given when the house was built I’m doubting the floors are even, so putting a floating on top will be a really bad option as they will wobble. And, installing wood on top of thin wood is a really bad solution. If your foundation is weak, your floor will be weak and it will creak and separate. Hardwood Floor
Judy – I’m sorry to hear this. I am surprised, but it does happen once in a while. I would probably get a 2nd opinion just to make sure. If they were solid hardwood and are now too thin, then it sounds like they’ve been refinished many times. Generally solid hardwood flooring is 3/4″ thick and that is what you should get if you put in anything new. That will then last a long time and you won’t have this issue in the future. Denver Hardwood Floor Install
Tongue-and-groove: One side and one end of the plank have a groove, the other side and end have a tongue (protruding wood along an edge's center). The tongue and groove fit snugly together, thus joining or aligning the planks, and are not visible once joined. Tongue-and-groove flooring can be installed by glue-down (both engineered and solid), floating (mostly engineered only), or nail-down (not recommended for most engineered).

Before you choose a hardwood floor, think about how much foot traffic you expect. Consider the look you want and how much you plan to invest. And, if you’re still undecided, browse our selection of other flooring options, including vinyl flooring, tile, parquet, and laminate flooring. You can also find helpful information in our cost guide. From selection to delivery and installation, the Home Depot is your one-stop shop for all your flooring needs. Denver Hardwood Floor Install

Visual – While hardwood flooring is limited by species and stains, Rigid Core flooring has near limitless options when it comes to flooring that looks like wood. In addition to traditional wood visuals and colors, you can pick from stone looks and even hybrids that marry wood and stones together into unique new options. And best of all you will benefit from a curated look that removes unwanted imperfections like oversized knots, holes, and worming that naturally occurs in hardwood floors. Denver Hardwood Flooring
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Hardwood Floor
Wood flooring can also be installed utilizing the glue-down method. This is an especially popular method for solid parquet flooring installations on concrete sub-floors. Additionally, engineered wood flooring may use the glue-down method as well. A layer of mastic is placed onto the sub-floor using a trowel similar to those used in laying ceramic tile. The wood pieces are then laid on top of the glue and hammered into place using a rubber mallet and a protected 2x4 to create a level floor. Often the parquet floor will require sanding and re-finishing after the glue-down installation method due to the small size pieces. Hardwood Floor

Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store.
Floor connection system: There are a wide range of connection systems, as most of them are mill-specific manufacturing techniques. The general principle is to have grooves on all four sides of the plank with a separate, unconnected, piece that is inserted into the grooves of two planks to join them. The piece used for the connection can be made from wood, rubber, or plastic. This installation system allows for different materials (i.e. wood and metal) to be installed together if they have the same connection system. Denver Hardwood Floor Install
We live in a 1924 home with very heavy thick oak woodwork thru out. It also has oak floors, quarter sawn in narrow strips, that In most rooms are in need of refinishing. We had a professional come & take a look yesterday, she said the flooring is too thin to sand & refinish. I was shocked, the floors have never been refinished. I was so disappointed. What can be done, if anything? We also have extended our kitchen & wanted to put oak flooring down to match the rest of the house. She said they don’t make this thickness anymore & the new flooring would be much thicker, therefore making it higher than the dining room that opens to it.

Measure rooms one at a time. It’s easiest to measure rectangles, so if you have an “L-shaped” room, divide it into 2 rectangles and measure them separately. The length of the rectangle multiplied by the width equals the square footage. For example, a room, or section of a room, that is 20 feet long and 12 feet wide produces this formula: 20 x 12 = 240 square feet. If the flooring you are purchasing is sold by the yard, divide the square feet by 9. So, 240 square feet / 9 = 26.667 square yards.
Michael – The exotic woods are a bit more challenging to work with stain wise because they are naturally darker and redder. Yes, you can refinish them and make them darker and browner. But, you will still have some underlying red tones. So, you may need to go darker than what you’re thinking to drown out the red more. Definitely test colors. Most likely, dark walnut will come out the darkest. Use duraseal…it’s a better stain, dries faster and is a bit darker than minwax. Denver Hardwood Floor
This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Denver Hardwood Flooring
Choose your replacement hardwood flooring. You don't have to replace your old floor with the exact same wood or flooring type that you just removed! You can glue your new hardwood flooring into place if you like. You can also install nail-down, floating (or locking) hardwood flooring as a replacement. The choice is up to you and what your budget allows.
This durable prefinished solid real wood floor will This durable prefinished solid real wood floor will enhance the value of your home. The flooring is made of 3/4 in. thick sawn solid wood and features mother nature's naturally occurring beauty marks such as distinctive color variation knots and mineral streaks. Plank length is totally random and varies based ...  More + Product Details Close Hardwood Floor
Price is the first obvious variable to consider. It is almost always cheaper to refinish your floor than to replace it. When replacing, you must consider the cost of the new wood as well as the installation. You can offset much of this cost by installing the floor yourself, but this is a very invasive process that requires specialized knowledge and precision. You can typically refinish a wood floor yourself, with just a few inexpensive solutions. Denver Hardwood Floor

Put on gloves, knee pads, and protective eye glasses. You'll be working diligently on your hands and knees for hours to complete this project, especially if you're doing a large space. Invest in a good pair of knee pads to protect your knees. Sturdy work gloves will protect your hands from splinters, and goggles will prevent sawdust and other debris from getting into your eyes.[1]


Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Floor

Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Flooring


So, assuming you can’t refinish existing and you can’t afford to replace it now, then focus on the new kitchen and put solid oak there. It’s okay and very common for this to be higher than the rest and it’s easy enough to add a wood transition. And, then later, you will need to replace the existing worn down floors w/ solid oak, so they will eventually be the same height. Denver Hardwood Floor Install
Although hardwood floors are amazingly beautiful and durable, they are not indestructible. The best floor maintenance plan for hardwood floors include regular vacuuming or sweeping with a soft bristle broom, especially in high traffic areas. Removing dirt or grit from your floors will reduce scratches. Vacuums with rotary brush heads can also scratch your floors. Denver Hardwood Floor
Choose your replacement hardwood flooring. You don't have to replace your old floor with the exact same wood or flooring type that you just removed! You can glue your new hardwood flooring into place if you like. You can also install nail-down, floating (or locking) hardwood flooring as a replacement. The choice is up to you and what your budget allows. Denver Hardwood Floor Install
So, assuming you can’t refinish existing and you can’t afford to replace it now, then focus on the new kitchen and put solid oak there. It’s okay and very common for this to be higher than the rest and it’s easy enough to add a wood transition. And, then later, you will need to replace the existing worn down floors w/ solid oak, so they will eventually be the same height. Denver Hardwood Floor Install
As the name suggests, solid hardwood is a single, solid piece of wood. Its natural simplicity has made it a popular flooring choice for generations, but that same simplicity makes it less than ideal for modern homes. Wood is a naturally porous material, meaning it is soft, extremely prone to denting, and absorbs water like a sponge. All of these attributes are ideal for helping trees grow, but they don’t translate well to modern flooring. Floors today need to withstand heavy traffic, drops, scratches, and most importantly, spills. Denver Hardwood Floor Install
Put on gloves, knee pads, and protective eye glasses. You'll be working diligently on your hands and knees for hours to complete this project, especially if you're doing a large space. Invest in a good pair of knee pads to protect your knees. Sturdy work gloves will protect your hands from splinters, and goggles will prevent sawdust and other debris from getting into your eyes.[1] Denver Hardwood Floor

While the overall thickness of flooring is going to vary by category, it is still important to know what is contributing to that thickness. Engineered wood flooring can inflate thickness by adding more layers of plywood or particle board, but still only offer a thin veneer of real wood on top. The dense core allows for Rigid Core floors to be significantly thinner than traditional hardwood floors, with WPC floors being thicker than SPC products. That doesn’t mean all Rigid Core floors are made equally though. Just like how engineered hardwood flooring can inflate thickness, Rigid Core flooring can alter the overall thickness by increasing the size of the acoustical padding on the back. While this padding adds a lot of great features, it doesn’t need to be any thicker than 1mm in size. When it comes to Rigid Core flooring, the thickness of the core is most important.
If you get a second opinion and they can’t be refinished, then your best option will be replace them…or wait until you can replace them. Given when the house was built I’m doubting the floors are even, so putting a floating on top will be a really bad option as they will wobble. And, installing wood on top of thin wood is a really bad solution. If your foundation is weak, your floor will be weak and it will creak and separate.
– If you want to change the width of the wood or the direction of the hardwood, the only way to do this is to get a new floor. The standard in home is oak 2 ¼” strip. Now, it’s more stylish and more common to get wider planks such as 3 ¼” or 4”or 5” planks. These look more modern and importantly make the room look larger. Another design trick to make the rooms look larger is to lay the planks on a diagonal – that way, it carries your eye along the longest length of the room. Or, you can even get fancy and add borders or do a herringbone pattern. Denver Hardwood Flooring

Regardless of the floor, the protective finish will play a large role in how scratch and stain resistant it is. Both hardwood and Rigid Core flooring are available with various types of protective finishes. Rigid Core flooring goes a step beyond hardwood though, and also has a transparent solid wear layer that protects against gouging and deeper scratches. Hardwood Floor


All varieties provide increased durability over traditional wood, but buying engineered wood with more core layers and a thicker veneer offers the most durability. Engineered flooring is available in a wide range of woods, colors and finishes. Here are a few of the most popular engineered flooring options, along with some unique characteristics of each and average pricing:
First, most people are unable to successfully refinish the floors themselves. It takes a lot of experience to refinish properly. Most people can’t get it smooth/even and also don’t realize that you need to sand them 3 times before putting the stain on. It’s even harder to do it right if they are pine or maple floors (and if they are, they require conditioner before stain is applied). Also, once the floors have been sanded unevenly by a non-professonal, it’s even harder to correct due to the waves usually created by the non-professional. Denver Hardwood Flooring

Natural warmth and beauty make wood a favorite for floors. But when the topcoat finish wears through, the porous surface of the wood is open to stains-especially beneath dining room chairs, in front of a sink and in other high-traffic, high-spill areas. Oil soap and all-purpose cleanser remove some stains, especially when the spill is fresh. But it's impossible to scrub out stains that have soaked into the wood fibers. And sanding only creates a depression in the floor that's more noticeable than the stain. The only option to repair hardwood floors at this point is to cut out the stained floorboards and install new ones. We replaced a couple of boards from a standard 3/4-in.-thick x 21/4-in.-wide oak-strip floor using a drill, circular saw and sharp chisel. To determine the exact width and thickness of the pieces you'll need, lift up a heat register or threshold and measure the exposed ends of the floorboards. You'll find hardwood flooring at a local millwork shop, lumberyard or floor-covering store. Denver Hardwood Floor


This process involves treating the wood by boiling the log in water. After preparation, the wood is peeled by a blade starting from the outside of the log and working toward the center, thus creating a wood veneer. The veneer is then pressed flat with high pressure. This style of manufacturing tends to have problems with the wood cupping or curling back to its original shape. Rotary-peeled engineered hardwoods tend to have a plywood appearance in the grain.[3] Denver Hardwood Flooring
With their increased durability and moisture resistance, engineered wood floors are a better option than traditional hardwoods if you have pets or spill-prone kids. Additionally, you can install engineered wood flooring in places that hardwoods typically can't go, including basements, kitchens and summer homes in high-humidity climates. This type of flooring is available in a variety of widths, colors and styles, including glue-down and floating floors.
Measure rooms one at a time. It’s easiest to measure rectangles, so if you have an “L-shaped” room, divide it into 2 rectangles and measure them separately. The length of the rectangle multiplied by the width equals the square footage. For example, a room, or section of a room, that is 20 feet long and 12 feet wide produces this formula: 20 x 12 = 240 square feet. If the flooring you are purchasing is sold by the yard, divide the square feet by 9. So, 240 square feet / 9 = 26.667 square yards.
"Click" or Woodloc systems: there are a number of patented "click" systems that now exist. These click systems are either "unilin" or "fiboloc" A "click" floor is similar to tongue-and-groove, but instead of fitting directly into the groove, the board must be angled or "tapped" in to make the curved or barbed tongue fit into the modified groove. No adhesive is used when installing a "click" floor, making board replacement easier. This system not only exists for engineered wood floors but also engineered bamboo and a small number of solid floors (such as "parador solido click") and is designed to be used for floating installations. It is beneficial for the Do-It-Yourself market.
If you’re thinking about redoing your hardwood floor, you might envision a refreshed look to your kitchen or hallway. You can picture your friends coming to your home for your next party and admiring your new floor, but you may find something standing in the way — you have no idea which type of hardwood flooring to get. With some research on your end, you can save yourself time and money. Let’s explore the features of some popular hardwood flooring types. Hardwood Floor
×